GREAT PLANES YAK-55M Yakovlev 사용 설명서 - 페이지 4

{카테고리_이름} GREAT PLANES YAK-55M Yakovlev에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. GREAT PLANES YAK-55M Yakovlev 20 페이지. Arf plane

페이지 인쇄
GREAT PLANES YAK-55M Yakovlev 사용 설명서

ADDITIONAL ITEMS REQUIRED

Adhesives and Building Supplies

This is the list of adhesives and building supplies required
to finish the Yak-55M EP. Order numbers are provided in
parentheses.
❏
1/2 oz. [15g] Thin Pro
❏
Pro 30-minute epoxy (GPMR6043)
❏
Threadlocker thread locking cement (GPMR6060)
❏
Denatured alcohol (for epoxy clean up)
❏
Paper towels
❏
Drill bits: 1/16" [1.6mm], 3/32" [2.4mm]
❏
#1 Hobby knife (RMXR6903)
❏
#11 blades (5-pack RMXR6930)
❏
Small T-pins (100, HCAR5100)
❏
Tape measure
❏
Pliers with wire cutter (HCAR0625)
❏
Phillips Head screw driver
❏
Masking tape
❏
Metal cutting file

Optional Supplies and Tools

Here is a list of optional tools mentioned in the manual that
will help you build the Yak-55M EP.
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Pro 6-minute epoxy (GPMR6042)
❏
Epoxy brushes (6, GPMR8060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
™
AccuThrow
Deflection Gauge (GPMR2405)
❏
™
CG Machine
(GPMR2400)
❏
21st Century
®
sealing iron [COCR2700]
❏
21st Century iron cover [COVR2702]
™
CA (GPMR6001)

IMPORTANT BUILDING NOTES

• There are three types of screws used in this kit:
Sheet metal screws are designated by
a number and a length. For example,
#6 x 3/4" [19mm]
Machine screws are designated by a
number, threads per inch, and a length.
For example 4-40 x 3/4" [19mm]
• When you see the term test fit in the instructions, it means
that you should first position the part on the assembly
without using any glue, and then slightly modify or custom
fit the part as necessary for the best fit.
• Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When
a specific type of adhesive works best for that step, the
instructions will make a recommendation.
• We recommend 30-minute epoxy to install the stabilizer,
because you will need the working time. 6-minute epoxy can
be used for the remaining assembly, but 30-minute epoxy
can also be used.
• Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following steps
to get another view of the same parts.
• The Yak-55M EP is factory-covered with Top Flite
MonoKote
®
film. Should repairs ever be required, MonoKote
can be patched with additional MonoKote purchased
separately. MonoKote is packaged in six-foot rolls, but
some hobby shops also sell it by the foot. If only a small
piece of MonoKote is needed for a minor patch, perhaps a
fellow modeler would give you some. MonoKote is applied
with a model airplane covering iron, but in an emergency a
regular iron could be used. A roll of MonoKote includes full
instructions for application. Following are the colors used on
this model and order numbers for six foot rolls.
White (TOPOQ0204)
Sapphire Blue (TOPQ0226)
True Red (TOPQ0227)

KIT INSPECTION

Before starting to build, take an inventory of this kit to make
sure it is complete, and inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not of
acceptable quality, or if you need assistance with assembly,
contact Product Support. When reporting defective or
missing parts, use the part names exactly as they are written
in the Kit Contents list.
Great Planes Product Support:
3002 N Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970, ext. 5
Fax: (217) 398-7721
4
®