AutomationDirect CLICK C0-04TRS-10 매뉴얼 - 페이지 2

{카테고리_이름} AutomationDirect CLICK C0-04TRS-10에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AutomationDirect CLICK C0-04TRS-10 3 페이지. Expansion i/o module

페이지 인쇄

C0-04TRS-10 CLICK Expansion I/O Module

Installation and Mounting

1. Safety Installation, Wiring or Handling

• Discharge static electricity before installation or wiring in order to avoid

electric equipment damage.

2. Preface

• CLICK C0-04TRS-10 is supported by CLICK Programming software

Ver 2.60 or higher.

3. Compliant Crimp-type terminal

• I/O terminals

4. The following crimping ferrules are recommended for 24VDC terminal and

I/O terminals of CPU and Expansion I/O.

Company

Series

Zoller+Fröhlich

Twin Ferrules

* Rated torque is 0.5 N·m. Take care not to contact adjacent terminal.

5. Safety Standard

• To comply with safety standards, please observe and use the following.

Please use SELV (as defined by UL61010-2-201) and Limited Energy

(as defined by UL61010-1, 9.4)

Please ensure basic isolation is provided between each relay block.

In order to comply with IEC/UL 61010-2-201 if the output is connected

to a circuit lower than 30V, please provide an external isolation before

the relay output terminals. Basic isolation requires an air separation

of at least 1.5 mm, a creepage distance of at least 2.5 mm, and a

withstand voltage of 1500V rms.

Installing Expansion I/O Modules:

• Remove protective cover over bus port.

• Push the LOCK slide (top and bottom of modules) to "UNLOCK".

• Align module pins and tabs (attachment of modules) into adjacent

slots and firmly push together.

• Push the LOCK slides to "LOCK" to lock modules rigidly together.

Modules easily connect to each other.

OPEN

To remove an I/O module, first disconnect all phases of external

power source and wait

5 seconds

expansion I/O module of a functioning system.

Then push LOCK slides to "UNLOCK" and gently separate modules.

www.automationdirect.com/click-plc

Model No.

Compliant Wire

* 0.5 mm

V30AE001134

(20AWG)

Locking Slides (Top and Bottom)

CLOSED

before installing or removing the

Additional Help and Support

• For additional technical support or questions, call our Technical

Support team @ 1-800-633-0405 or 770-844-4200

Safety Installation

Please heed the following instructions when

installing:

• Mount the CLICK PLC unit horizontally to provide

proper ventilation.

• Do not mount the CLICK PLC unit upside down, on

a horizontal surface, or in a vertical arrangement.

• There is a minimum clearance requirement of

2in. (51mm) from all sides of the cabinet and the

equipment.

• There is a minimum clearance requirement of 3in.

(76mm) from the wiring ducts and the equipment

• Please use this product in a metal enclosure/cabinet.

Air

Flow

Enclosures

It is important to select the appropriate enclosure to ensure safe and proper

operation of your CLICK PLC system. Control applications vary and yours may

require additional considerations. At a minimum your enclosure should include:

• Conformance to electrical standards

• Protection from the elements in an industrial environment

• Common ground reference

• Maintenance of specified ambient temperature

• Access to equipment

• Security or restricted access

• Sufficient space for proper installation and maintenance of equipment

• When installing modules and CPU on DIN rails, always

use end brackets on both ends of assembly.

• You should use 35mm width DIN Rails.

• You should use M4 size screws when you surface mount.

• You should tighten the screws with a spring washer and

a small round washer and torque (0.5 to 0.6 N·m).

Do not operate without first installing safety cover over power supply

CLK-2

CLICK Module Insert

3505 HUTCHINSON ROAD

CUMMING, GA 30040-5860

Minimum clearance requirement

51mm

of 51mm for A, B, and C.

CAUTION

leads.

1-800-633-0405