ADEMCO 5817CB 설치 지침

{카테고리_이름} ADEMCO 5817CB에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO 5817CB 4 페이지. Wireless commercial / household transmitter
ADEMCO 5817CB에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 설치 및 설정 매뉴얼 (2 페이지), 설치 지침 (2 페이지), 설치 및 설정 매뉴얼 (2 페이지)

페이지 인쇄

GENERAL INFORMATION

The 5817CB is a universal contact-monitoring transmitter that can be used with household

and commercial fire and burglary-initiating devices such as door/window contacts, motion

and glassbreak detectors, sprinkler water flow switches, tamper switches, post indicator

valves, manual pull stations, and remote duct detectors. Upon activation, it emits an RF

signal to a control panel that sends a burglary or fire alarm to a central station. The 5817CB

has three unique input loops (zones). The first loop (primary loop) is supervised and typically

used for high-priority alarm reporting such as commercial fire or burglary. It requires a

470K ohm end-of-line resistor to be placed across the sensor. The second loop is the built-in,

normally closed reed switch (used in conjunction with a magnet, as described below). The

third loop is another normally closed household burglary loop. All three loops may be used. A

fourth (automatically enrolled) loop contains two tamper switches to protect the 5817CB

transmitter. A built-in cover tamper switch is activated when the cover is removed. A unit

tamper switch is activated if the unit is separated from its mounting plate.

The 5817CB has its own unique serial number permanently assigned during manufacture.

You must "enroll" this transmitter serial number in the control panel at some point prior to

its usage in the alarm system. Refer to the control panel's installation instructions for

further details. Note: During programming of the control panel, program the 5817CB

transmitter as Input Type "RF" (i.e., supervised RF) ( mandatory for UL installations ).

MOUNTING

For proper orientation of the unit in relation to its wall mounting plate and the loop wiring,

read all of this section before installing the unit.

permanently, conduct Go/No Go tests (see control's instructions) to verify adequate signal

strength from location. When a satisfactory location is found, remove the battery and proceed

with installation.

The following mounting instructions assume that the unit will be mounted as shown in the

diagrams. The unit may, however, be installed in any direction, as long as the relationship of

the unit to its mounting plate is maintained.

The mounting plate, installed as described below, enables easy removal of the unit for

servicing, should it become necessary.

1. Remove the transmitter's cover by inserting the flat blade of a small screwdriver into

the pry-off slot at the bottom end of the unit on the right side closest to the cover's

decorative ribs and twisting.

2. Disengage the supplied mounting plate from the unit by inserting the blade of a

small screwdriver into the mounting plate release hole (see Diagram 2) and pushing the

locking tab out (see Diagram 1). Slide the mounting plate downward along the case back.

Note : For this application, the alignment guide strip along one edge of the mounting

plate serves no function and may be broken away, if desired.

3. If concealed wiring is to be used, feed the wires through the concealed wiring entry

hole at one corner of the plate ( surface wiring is mentioned in Step 5 below).

4. Install the mounting plate, with its case-holding posts pointing up, in the location

selected, as described in the control unit's installation instructions. Use the two flat-head

screws supplied. Note: To ensure proper operation of the unit's back tamper (when it is

separated from the mounting plate), the screws must be anchored to a wall stud or other

solid wood material.

5. If surface wiring is to be used, remove the knockout slot in the case back (located

across from loop 3 terminal block). Surface wiring should enter through this knocked

out space provided. Do not connect the wiring to the terminal block(s) yet.

INSTALLATION INSTRUCTIONS

WIRELESS COMMERCIAL

HOUSEHOLD TRANSMITTER

Before mounting the transmitter

K5623V1 4/01

5817CB