AutoMeter AutoZone DXC-2018CA 빠른 시작 매뉴얼 - 페이지 2
{카테고리_이름} AutoMeter AutoZone DXC-2018CA에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AutoMeter AutoZone DXC-2018CA 2 페이지. Battery charging system
페이지 인쇄
WARNING: Safety glasses or goggles must be worn when using the charger.
Charging a battery
1. Startup screen will be displayed automatically when unit is first turned on.
Press ʻYʼ for menu.
2. Menu screen will display cursor pointing to
Press ʻYʼ to continue.
3. Connect clamps to battery.
The DXC-2018CA will automatically
proceed to the next function.
4. Enter the approximate battery temperature. Use the + / Up and the - / Down keys
to change the temperature. Press Y / Enter key to continue once the temperature
has been entered.
5. Enter the CCA rating for the battery. Use the + / Up and the - / Down keys to change
the rating. Press Y / Enter key to continue once the rating has been entered.
6. Scroll down to
choose type
of battery.
7. Fast Charge Mode: Quickly charges the battery up to level that it can be put
back into service, and the remaining charge will be put back into the battery
with the vehicles charging system. Full Charge Mode: Provides a full charge
to the battery. Charge times will be longer compared to the Fast Charge Mode.
8. Confirm Inputs. If inputs are correct, Press ʻYʼ to continue
If changes are required, Press ʻNʼ to re-enter battery information.
9. Battery Charging Begins. After a short time, the display will indicate the
maximum time to complete the charge.
10. Charge Results/Trustworthy Advice are displayed. Trustworthy Advice can be
viewed on screen by scrolling down using the - / Down button.
Charged Battery
Failed to Charge
Weak Charge
®
How to Use the Battery Charger
WARNING: Use caution handling if battery temperature exceeds 140°.
Red clamp
Black clamp to (-) Negative battery post
NOTE: If the battery is over 120°F, the DXC-2018CA will prompt you to
allow the battery to cool before proceeding with charging the battery.
Starting Standard
(Examples: Duralast Gold,
Duralast, ValuCraft and
other starting batteries.)
Charge is complete.
Battery would not accept charge.
Perform a Charge and Test on a DDC-2010.
Battery may not be accepting a normal charge.
Perform a Charge and Test on a DDC-2010.
For Technical Assistance Call
888-453-2244
>
Charge.
to
(+) Positive
Optima Red
Starting AGM
Optima Yellow
Deep Cycle AGM
Optima Blue
Deep Cycle STD
Gell Cell
AUTO METER
DXC-2018CA
SMART CHARGER
'Y' FOR MENU.
>CHARGE
REVIEW/PRINT
SETUP
ABOUT
battery post
>CONNECT CLAMPS
TO BATTERY.
RED + BLACK -
'N' TO CANCEL.
>ENTER BATTERY
TEMP.:
USE +/-.
'Y' TO CONTINUE
>ENTER RATED CCA
USE +/-.
'Y' TO CONTINUE
CHOOSE BATT TYPE
STARTING STANDRD
USE +/-.
'Y' TO CONTINUE
CHOOSE CHRG TYPE
FAST CHARGE
USE +/-.
'Y' TO CONTINUE
STARTING STANDRD
TEMP. 73F
RATED CCA
'N' OR 'Y'
CHARGING
MAX TIME:
'N' TO STOP
C#9 12V BATT.
CHARGED
14.88 CHRG 100%
'Y' TO PRINT
C#10 12V BATT.
FAILED TO CHARGE
10.28V CHRG 0%
'Y' TO PRINT - MORE
C#12
WEAK CHARGE
13.50V CHRG 100%
'Y' PRINT - MORE
2650-1935-77 1/9/17
70F
600
FAST
600
0:30
BATT.
2