Dynamite DYN4060 매뉴얼 - 페이지 3
{카테고리_이름} Dynamite DYN4060에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynamite DYN4060 4 페이지. Ac/dc li-po charger
페이지 인쇄
Charging Process
Step 1: Connect the battery to the charger using the appropriate
charge cord. Be sure to connect the battery with respect to
proper polarity. The charger will signal the connection of the
battery by producing one long beep. The LED will also flash
indicating the connection of the battery.
Step 2: Press the Cell Selection/Start Button to choose the
proper cell count to match your battery pack.
Step 3: Refer to the chart below for recommended charge rates.
Select the appropriate charge rate for your particular battery by
actuating the Charge Rate button.
Battery Capacity
500mAH–1500mAH
1500mAH–3500mAH
3500mAH and above
Warning: Selecting a charge rate higher than 1x battery
capacity may result in fire.
Step 4: Push and hold the Start button for two seconds. You will
hear a short beep, and the LED will remain on continuously to
indicate the battery is charging.
Note: Do not adjust the charge rate switch in this state.
Note: The charge cycle can be canceled by pressing the
Start button again. The charger will produce a short beep
to indicate the end of the charge cycle, and the LED will
again flash.
• The charger will detect the cell count to make sure the correct
cell count has been selected. If not, the charger will emit an
error tone and all the charge LED' s will flash.
• If the battery voltage is too low, the charger will also emit
the error tone even though the right number of cells has been
selected. Hold the CHARGE button for 2 seconds to enter the
charger into the low voltage charge mode. After 30 seconds the
charger will return to the correct charge mode.
Step 5: When charging is complete, the charger will emit one
long beep, ten double-beeps and then the LED will flash.
The beeper will sound every 45 seconds until the battery is
disconnected. Do not leave the battery connected to the charger
when charging is complete. Failure to comply may result in fire.
Charge Rate
500mA
1500mA
3500mA
Warranty
Limited Warranty Period
Horizon Hobby, Inc. guarantees this product to be free from
defects in both material and workmanship for a period of 5 years
from the date of purchase.
Limited Warranty & Limits of Liability
Pursuant to this Limited Warranty, Horizon Hobby, Inc. will, at
its option, (i) repair or (ii) replace, any product determined by
Horizon Hobby, Inc. to be defective.
In the event of a defect, these are your exclusive
remedies.
This warranty does not cover cosmetic damage or damage
due to acts of God, accident, misuse, abuse, negligence,
commercial use, or modification of or to any part of the
product. This warranty does not cover damage due to improper
installation, operation, maintenance, or attempted repair by
anyone other than an authorized Horizon Hobby, Inc. service
center. This warranty is limited to the original purchaser and
is not transferable. In no case shall Horizon Hobby' s liability
exceed the original cost of the purchased product and will not
cover consequential, incidental or collateral damage. Horizon
Hobby, Inc. reserves the right to inspect any and all equipment
involved in a warranty claim. Repair or replacement decisions
are at the sole discretion of Horizon Hobby, Inc. Further, Horizon
Hobby reserves the right to change or modify this warranty
without notice.
REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. HORIZON HOBBY, INC. SHALL NOT BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
As Horizon Hobby, Inc. has no control over use,
setup, final assembly, modification or misuse, no
liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or
assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the
liability associated with the use of this product, you are advised
to return this product immediately in new and unused condition
to the place of purchase.