2gig Technologies 2GIG BRDG1 900 설치 지침 - 페이지 3

{카테고리_이름} 2gig Technologies 2GIG BRDG1 900에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG BRDG1 900 4 페이지. Bridge ip communicator

페이지 인쇄

A summary screen displays the following information:

• Network Configuration. The network type configuration.

• IP Address. The IP Address for the Go!Bridge. This is a 32‐bit

numeric address that identifies the device on the network.

• Subnet Mask. The subnet mask for the network. All devices

that are joined to a network belong to a subnetwork.

• Gateway. The IP Address for the access point to the external

network. Typically, this is the IP Address of the local network

router or node that control traffic for your ISP.

• MAC Address. This is the Media Access Control (MAC)

Address. It is a physical address that is encoded to the

Go!Bridge during the manufacturing process.

Testing

The Go!Bridge tests the network connection to the third‐party

monitoring service. A report shows if Go!Bridge has successfully

connected (or failed to connect) to the external server.

Registration

To register the Go!Bridge with the monitoring service, refer to your

specific provider's registration instructions.

SPECIFICATIONS

Wireless Signal Range

500 ft (152.4 m), open air, with Wireless Control

Panel

Silicon Labs SI1001‐E‐GM2

Transceiver

Transceiver Frequency

25 channel frequency‐hopping spread spectrum,

403 kHz channel spacing (910.2‐920.275 MHz)

Modulation Type

GFSK modulation, 128 kpbs

+19dBm Maximum

RF Power

Ethernet

10/100 BaseT

Dimensions (L x W x H)

6.24 x 4.5 x 1 in (159 x 114 x 25 cm)

Weight

9.6 oz

Housing Material

Cycoloy™ Resin C2800 (Rated to UL 94 V‐0:

Flammability Standard)

Color

White

32° F to 120.2° F, (0° C to +49° C)

Operating Temperature

Relative Humidity

5‐95% Non‐Condensing

5VDC

Operating Voltage

Certification

ETL, FCC Part 15, and Industry Canada

IMPORTANT NOTE

Should the local network lose Internet access due to a power outage

or interruption, the Go!Bridge is not equipped with a backup battery

system. To best prepare for power failures and to ensure the security

system maintains Internet access with the monitoring service for life‐

safety communications during power failures, the local network must

have a dedicated Uninterrupted Power Supply (UPS) or backup battery

solution from a third‐party manufacturer in place. Linear LLC does not

supply, provide, recommend, or test the Go!Bridge with any UPS or

battery backup solution. It is also assumed that owner's Internet

Service Provider (ISP) maintains a backup battery (or power

generator) for their remote network equipment.

REGULATORY INFORMATION

Wireless Product Notice

Radio controls provide a reliable communications link and fill an

important need in portable wireless signaling; however, there are

some limitations which must be observed.

• For United States Installations Only: The radios are required to

comply with FCC Rules and Regulations as Part 15 devices. As

such, they have limited transmitter power and therefore

limited range (approximately 400 ft.).

• A receiver cannot respond to more than one (1) transmitted

signal at a time and may be blocked by radio signals that occur

on or near their operating frequencies, regardless of code

settings.

• Changes or modifications to the device may void FCC

compliance.

• Infrequently used radio links should be tested regularly to

protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained

prior to acting as a wholesale distributor or dealer, and these

facts should be communicated to the end users.

ETL Listed

This device has been tested by Intertek and is in

compliance with UL 1023: Household Burglar‐Alarm

System Units in the United States and Canada.

FCC Part 15 Notice

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits

for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one (1)

or more of the following measures.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for

help

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate

the equipment.

Les changements ou modifications non approuvés expressément par

la partie responsable de la conformité pourrait annuler l'autorité de

l'utilisateur à faire fonctionner l'équipement.

Industry Canada (IC) Compliance

This device complies with Industry Canada license‐exempt RSS

standard(s). Operation is subject to the following two conditions: (1)

this device may not cause interference, and (2) this device must accept

any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

Repairs to certified equipment should be made by an authorized

Canadian maintenance facility designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment