8STREME Black Pearl 매뉴얼 - 페이지 7
{카테고리_이름} 8STREME Black Pearl에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 8STREME Black Pearl 9 페이지. Autonomous swimming pool cleaner
페이지 인쇄
09 Indicator lights / LED
C
E
Page 11
INDICATOR
MEANING / DIAGNOSIS
LIGHT/LED
When the power supply is plugged into wall outlet and
A
toggle switch is pressed towards "ON", this blue light must
remain on to indicate that the power supply is operating
normally. Otherwise check if the wall outlet has power or
replace the transformer.
B
It is a timer indicator. This red or orange light will light up
during the cleaning cycles (orange for 1 hour cycle - red for
3 hour cycle).
This blue light turns on when the floating cord between
C
the transformer and the No-Twist float with swivel union is
properly connected and you have turned on the robot. It
indicates that the current is reaching the float. If the light
does not come on, check the connections.
This green light only lights up when the robot pump is
D
running. This green light does not light up when the pool
robot has completed its cleaning cycle or during certain
phases of the device's operation (e. g. after climbing walls,
when pump stops and the robot sinks).
When the "No-Twist" float with rotating swivel is connected
E
to the transformer and you have started the robot, this small
red light indicates that the current is coming out of the
float. You must have both this red light and the blue light (C)
on the float. If you have the blue light on the float but not
the red light, then it is likely that you will need to replace
the float.
10
TROUBLESHOOTING
PROBLEM
- Immersion of the robot in the pool.
- Use of the fine filter.
The robot floats on the surface.
- Water level in the pool.
The robot does not clean all areas of the pool.
- Not enough/ too much cable floating in the pool.
- The robot does not receive enough power.
The robot does not recover debris during operation.
- Basket clogged/ full.
Fine particles (dust or dirt, pollen ... ) are ejected by
-
An object is stuck in the impeller or the grid
the impeller.
located above the impeller.
-
Debris are too fine, the robot is made to pick upthe
particles more than 50 microns (with the fine filter
inside the basket).
CAUSE(S)
SOLUTION(S)
- When you put the robot in the pool, let it sink and
reach the floor before you turn it on.
-
If you use an optional fine filter, remove the filter
from its plastic wrap, immerse the filter in the water
so that it is already wet before you put it in the robot
and let the robot settle on the floor before you turn
it on.
-
If your pool water level is too high, the robot might
turn around and take in the air if it touches the fop
seats, in this case to adjust the level of the pool.
- Make sure the length of floating cable introduced in
the pool is just the required length.
- Remove any excess cable length from the pool and
leave this excess length outside the pool next to the
power supply box.
- Insert the robot at the center point of the pool.
If your pool is oval or rectangular, this point is the
middle of the length.
- Check the connection of the cables.
- Clean the basket and filter panels. Clean the fine
filter if you use this accessory.
- Check if the basket is properly inserted. (See
chapter Cleaning of the filter basket).
-
Check that there are no foreign objects in the
impeller or blocked in the grid above the impeller
-
Check the attachment of the basket, press it if
necessary to lock it.
- Use a fine filter (check item number on the parts
drawing 29, sku 7117) on the
other hand do not forget that it is the filtration of
your swimming pool which ensures the cleaning
of the particles of less than 50 microns.
Page 12