8STREME Black Pearl 매뉴얼 - 페이지 8
{카테고리_이름} 8STREME Black Pearl에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 8STREME Black Pearl 9 페이지. Autonomous swimming pool cleaner
페이지 인쇄
PROBLEM
The robot moves in one direction.
- An object blocks the rollers, the wheels of the robot
I
or interfering with the movement of the robot.
The robot does not move and the filtration pump
- The robot is not connected to a
power source.
does not work either. The robot doesn't work any
longer.
- Power is off.
I
The pump runs but the robot does not
- No/not enough power is transmitted to the robot.
move. The robot turns on but stays in one
- An object blocks the rollers, the belts, the wheels
spot.
of the robot or the path.
- Possibility of motor problem.
- The robot is too heavy.
Robot does not climb walls.
- The flow is not enough.
- The walls are too slippery.
- The handle of the robot is correctly directed.
- pH level is too high. Keep the pH level close to
7.2 to avoid slippery walls
- A belt is damaged.
The robot goes round in circles.
- One of the 4 side wheels is damaged or unscrewed.
I
Page 13
SOLUTION(S)
CAUSE(S)
-
Check that there are no foreign objects i n the
impeller located above the motor.
- Check that there is no foreign object blocking the
hydraulic circuit or the brushes and belts under
therobot and sides.
- Check that the power source is active by plugging
another device into the power outlet.
- Check that the power supply is turned on.
- Check all connections of the robot to the power
source.
- Unplug the power and take out the robot in the
water. Open the cover of the basket and remove the
basket.
- Check that there are no foreign objects in the
impeller located above the motor.
- Check that there is no foreign object blocking the
hydraulic circuit or the brushes and belts under the
robot and sides.
- Contact the After-sales Service
- Check that the collection of debris basket isn't full
- Check and clean if needed the impeller of the pump
or the grill at the top of the impeller (propeller on top
of the robot toward the handle)
- Presence of algae or fatty deposits on the walls.
Remove algae using the chemical treatment of water
and manually brush to remove these fatty deposits.
- Check that the handle of the robot is directed to the
rear. The cable should be above the handle.
- Check the condition of the drive belts.
If necessary, replace any faulty belt.
- Check the wheels bolted to the ends of the rollers.
These wheels fit onto the roller and then screwed
on. (See Chapter 4)
PROBLEM
The robot stops after a few minutes.
- Connection of the floating cable.
- Possibility of fault of the floating cable.
- Possibility of motor leakage.
- The robot is too heavy.
The robot moves slower than before.
- The water flow is not sufficient.
- Cables connections loose/disconnected.
No LED lit on the transformer.
- The current is not reaching the transformer.
- Bad connection between the transformer and
The blue LED on the "No-Twist" floating device
the No-Twist floating device.
does not light up ( light C of Chapter 9).
- Possibility of No-Twist floating device problem
- You did not press the on/off button located
above the transformer.
The blue light on the transformer is on but the red
- Cleaner not activated
or orange do not light up (timer light B of Chapter 9).
- Bad cable connections.
- Possibility of ransformer problems
The blue light on the No-Twist Floating device is on
- Bad connection between the No-Twist floating
but the cleaner does not work ( light C of Chapter 9 ).
device and the cleaner
- Possibility of No-Twist floating device problem
- Possibility of motor problem.
The robot leaves traces on the floor or on the walls.
- State of the brushes and/or transmission belts.
Please contact www.8streme.com if you have any other questions.
CAUSE(S)
SOLUTION(S)
- Check the connections of the floating cable.
Disconnect and reconnect as needed.
- Check the status of the connectors at the ends of
your cables (damaged, rusted, etc.)
- Check that the dirt collecting basket is not full.
- Check and clean if necessary the pump impeller or
the grill above the impeller (propeller at the top of
the robot towards the handle).
-Check all the cable connections (see chapter 5).
-Check your electrical outlet.
-Check the cable connections.
-Contact our Customer Service.
-Turn ON the cleaner by pressing the ON/ OFF
button located on top of the transformer.
-Check all the connections of the cables between
the transformer and the No-Twist floating device.
-Contact the After-sales Service
-Turn ON the cleaner by pressing the ON/ OFF
button located on top of the transformer.
-Check your electrical outlet.
-Do not use extension cord
-Contact our Customer Service.
-Check if the connection at the "No-twist" float
outlet, blue outlet "Pool Cleaner", is correct and
waterproof.
-If the blue light C is on, you should also have a red
light on at the float outlet (light E in Chapter 8). If
this is not the case, it is likely that the float is
defective.
-If both blue and red lights are on but the robot does
not work, please contact your dealer or our after-
sales service at [email protected]
-These brushes and belts are wear-and-tear parts.
Please check them and change them if necessary.
Page 14