2gig Technologies 2GIG-BRDG1-900 설치 지침 - 페이지 2

{카테고리_이름} 2gig Technologies 2GIG-BRDG1-900에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 2gig Technologies 2GIG-BRDG1-900 4 페이지. Go!bridge ip communicator

페이지 인쇄

Go!Bridge IP Communicator | Installation Instructions

NOTE: If the 900MHz LED illuminates in GREEN (the lower LED),

verify that the network cable is not connected to the Go!Bridge

IP Communicator. If the cable is disconnected and it is still

illuminated GREEN, use the end of an open paperclip to press

and release the recessed Reset button. The button is located

inside the small hole on the port side of the Go!Bridge IP

Communicator, directly above the Ethernet port. This restores

the factory settings. See Figure 3 Go!Bridge IP Communicator

Rear View—Ports and Recessed Reset Button.

Figure 3 Go!Bridge IP Communicator Rear View

Recessed Reset Button

A Recessed Reset Button

B Ethernet Port

Power Supply Port

After the Go!Bridge IP Communicator is powered ON, continue with

Programming the Go!Bridge IP Communicator into the Control

Panel.

Programming the Go!Bridge IP Communicator

into the Control Panel

Use these steps to place the control panel and Go!Bridge IP

Communicator in learning mode. This gives the control panel the ability

to learn the network settings transmitted by the Go!Bridge IP

Communicator.

NOTE: To scroll between op ons on the control panel, tap the ←

and → arrows. To move to the previous or next prompt tap the

↑ and ↓ arrows.

Connect an Ethernet cable (not included) to the router and

Go!Bridge IP Communicator. Do not plug the cable into the uplink

port.

For compliance with UL 1023: Household Burglar‐

IMPORTANT:

Alarm System Units, the Go!Bridge must be installed in the

same room as the Internet modem or router.

Ensure the control panel is powered ON. Then tap the Home

button.

Tap the system logo in the lower‐right corner of the control panel

Home screen.

At the Enter Your Code screen, enter the four (4)‐digit master

installer code to go to the Installer Toolbox (1 of 2) screen.

At the Installer Toolbox (1 of 2) screen, tap System Configuration.

At the Q1: Select RF Sensor # (01 to 48) screen, tap Go To.

At the Enter Question Number (2 Digits) screen, enter 92.

At Q92 Select Network Device (0 to 1), tap → to scroll to (1)

Go!Bridge IP Communicator. Then tap ↓.

10 On the Go!Bridge IP Communicator, press and release the Learn

—

Ports and

11 At the Pair with Xcvr Device screen, tap OK. Then tap ↓ to

Configuring the Go!Bridge IP Communicator Settings

NOTE: A trouble alert consists of an audible beep and the Control

LED Indicators

The table details the LED indicators on the Go!Bridge IP Communicator.

Network LED

Solid GREEN

Flashing GREEN Network cable is plugged in and IP address is actively being

Solid RED

900 MHz LED

Solid GREEN

Flashing GREEN Linked to the Control Panel. Communication issues exist.

Solid RED

Flashing RED

At Q: Network Device ID (Read Only), tap Learn. This gives the

panel the ability to discover the read‐only network device ID

transmitted by the Go!Bridge IP Communicator.

At the Pair with Xcvr Device screen, the "initiating learning

process" message appears.

button (this is the small, black plastic button on the LED side of the

Go!Bridge IP Communicator below the 900MHz LED). This transmits

the device ID to the Control Panel.

When the "learn operation succeeded" message appears and the

panel displays the Type (Go!Bridge IP Communicator) and ID#, the

Go!Bridge IP Communicator and panel are linked. The 900MHz LED

on the Go!Bridge IP Communicator also flashes GREEN.

continue with Configuring the Go!Bridge IP Communicator Settings

below.

At the Q: Select Port # (1 to 8) screen, enter the port number for

the third‐party monitoring services' server. Then tap ↓.

At Q: Used (0 to 1), tap → to select one (1) of these options:

•

(0) Disabled (Recommended). This is the default setting. Most

users will keep this port disabled. Then tap Next and skip to

step 3.

•

(1) Enabled. Then tap ↓. At the Q: Enter Port Value (0‐65535)

screen, tap ↓ to accept the default port value. Next, at the Q:

Enter Port Forward IP Address screen, tap ↓ to accept the

address configured by the provider. You can configure up to

eight (8) ports. If you are finished configuring ports, tap Next.

At the Summary of Network Device screen, tap ↓. Verify the list of

port numbers and forward IP addresses appears as programmed.

Then tap Skip.

At Q93 Enter Broadband Network Failure Time (1 to 255), enter

the desired number of minutes that must pass before a network

failure triggers the Control Panel to issue a trouble alert. The

default value is 30 minutes. Then tap ↓.

Panel's Home screen displays a trouble message.

At Q94 Select Broadband Network Failure Report (0 or 1), tap → to

select whether or not to report the broadband network failure to

the monitoring service:

•

(1) Enabled. This is the default setting. Network failures are

reported to monitoring service.

•

(0) Disabled. Network failures are not reported.

Tap End.

At the Summary of System Configuration screen, verify the

settings. Then tap Save Changes.

Tap Exit to the close the System Configuration screen.

Globe Icon

Indicates the presence of an external network connection.

assigned.

Network cable unplugged.

Icon Labeled "900MHz"

Linked and communicating with the Control Panel.

Not linked to the Control Panel, turns solid after a device

reset.

Not linked to the Control Panel.