Autonics TCN4M Series 매뉴얼

{카테고리_이름} Autonics TCN4M Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics TCN4M Series 2 페이지. Dual display pid temperature controller
Autonics TCN4M Series에 대해서도 마찬가지입니다: 사용 설명서 (2 페이지), 매뉴얼 (13 페이지), 제품 설명서 (6 페이지)

페이지 인쇄

DUAL INDICATOR TEMPERATURE CONTROLLER

TCN4 SERIES

Thank you very much for selecting Autonics products.

For your safety, please read the following before using.

Caution for your safety

Please keep these instructions and review them before using this unit.

Please observe the cautions that follow;

Warning

Serious injury may result if instructions are not followed.

Product may be damaged, or injury may result if instructions are not

Caution

followed.

The following is an explanation of the symbols used in the operation manual.

Caution: Injury or danger may occur under special conditions.

Warning

1. In case of using this unit with machinery (Ex: nuclear power control, medical equipment, ship,

vehicle, train, airplane, combustion apparatus, safety device, crime/disaster prevention

equipment, etc) which may cause damages to human life or property, it is required to install

fail-safe device.

It may cause a fire, human injury or damage to property.

2. Install the unit on a panel.

It may cause electric shock.

3. Do not connect, inspect or repair this unit when power is on.

It may cause electric shock.

4. Wire properly after checking terminal number.

It may cause a fire.

5. Do not disassemble the case. Please contact us if it is required.

It may cause electric shock or a fire.

Caution

1. This unit shall not be used outdoors.

It may shorten the life cycle of the product or cause electric shock.

2. When connect wire, AWG 20(0.50mm

) should be used and screw bolt on terminal block with

0.74N.m to 0.90N.m strength.

It may cause a malfunction or fire due to contact failure.

3. Please observe the rated specifications.

It may shorten the life cycle of the product and cause a fire.

4. Do not use beyond of the rated switching capacity of relay contact.

It may cause insulation failure, contact melt, contact failure, relay broken and fire etc.

5. In cleaning unit, do not use water or organic solvent. And use dry cloth.

It may cause electric shock or a fire.

6. Do not use this unit in place where there are flammable or explosive gas, humidity, direct ray

of the light, radiant heat, vibration and impact etc.

It may cause a fire or an explosion.

7. Do not inflow dust or wire dregs into the unit.

It may cause a fire or a malfunction.

8. Please wire properly after checking the terminal polarity when connecting temperature sensor.

It may cause a fire or an explosion.

9. In order to install the units with reinforced insulation, use the power supply unit which basic

insulation level is ensured.

Ordering information

4 S

2 4 R

Control output

Relay contact output + SSRP output (AC power)

Relay contact output + SSR output (AC/DC power)

Power supply

24VAC 50/60Hz, 24-48VDC

100-240VAC 50/60Hz

Sub output

Alarm1 + Alarm2 output

DIN W48 X H48mm

Size

DIN W72 X H72mm

DIN W48 X H96mm

DIN W96 X H96mm

Digit

4Digit(9999)

Setting type

Dual display type, set by touch switch

Item

Temperature controller

The above specifications are subject to change without notice.

Speciﬁ cation

Series

TCN4S

TCN4M

TCN4H

100-240VAC 50/60Hz

Power

AC Power

supply

24VAC 50/60Hz, 24-48VDC

AC/DC Power

Allowable voltage range

90 to 110% of rated voltage

Max. 5VA(100-240VAC 50/60Hz, 24VAC 50/60Hz)

Power consumption

Max. 3W(24-48VDC)

Display method

7 Segment LED(PV: Red, SV: Green)

PV(WXH) 7.0 X 15.0mm

9.5 X 20.0mm

7.0 X 14.6mm

Character

size

SV(WXH) 5.0 X 9.5mm

7.5 X 15.0mm

6.0 X 12.0mm

RTD

DIN Pt100Ω, Cu50Ω (Allowable line resistance max.5Ω per a wire)

Input

type

K(CA), J(IC), L(IC), T(CC), R(PR), S(PR)

RTD

Based on room temperature (23ºC ± 5ºC): (PV ± 0.5% or ±1ºC higher one) rdg ± 1 Digit

Display

accuracy

In case of out of room temperature range: (PV ± 0.5% or ±2ºC higher one) rdg ± 1Digit

Relay

250VAC 3A 1a

Control

output

SSR

12VDC±2V 20mA Max.

Alarm output

AL1, AL2 Relay: 250VAC 1A 1a

Control method

ON/OFF control, P, PI, PD, PID control

Hysteresis

1 to 100

/0.1 to 50.0

ºC

Proportional band(P) 0.1 to 999.9

ºC

Integral time(I)

0 to 9999 sec.

Derivative time(D)

0 to 9999 sec.

Control period(T)

0.5 to 120.0 sec.

Manual reset

0.0 to 100.0%

Sampling period

100ms

AC power

2000VAC 50/60Hz 1min.(Between input terminal and power terminal)

Dielectric

strength

AC/DC power

1000VAC 50/60Hz 1min.(Between input terminal and power terminal)

Vibration

0.75mm amplitude at frequency of 5 to 55Hz in each X, Y, Z directions for 2 hours

Relay life

Control output Mechanical: Min. 5,000,000 operations, Electrical: Min. 200,000 operations (250VAC 3A resistive load)

cycle

Alarm output

Mechanical: Min. 5,000,000 operations, Electrical: Min. 300,000 operations (250VAC 1A resistive load)

Insulation resistance Min. 100MΩ(at 500VDC megger)

Noise immunity

Square-wave noise by noise simulator(pulse width 1㎲)

2KV R-phase and S-phase

Memory retention

Approx. 10 years (When using non-volatile semiconductor memory type)

Ambient

-10 to 50

ºC

, Storage: -20 to 60

ºC

Environ

Temperature

-ment

Ambient

35 to 85%RH, Storage: 35 to 85%RH

humidity

Unit weight

Approx. 100g

Approx. 133g

Approx. 124g

1: For display accuracy

- In case of room temperature (23ºC ± 5ºC)

Below 200ºC of thermocouple R, S is PV ± 0.5% or ±3ºC higher one ± 1 digit

Over 200ºC of thermocouple R, S is PV ± 0.5% or ±2ºC higher one ± 1 digit

Termocouple L (IC), RTD CU50Ω is PV ± 0.5% or ±2ºC higher one ± 1 digit

- In case of out of room temperature range

Below 200ºC of thermocouple R, S is PV ± 1.0% or ±6ºC higher one ± 1 digit

Over 200ºC of thermocouple R, S is PV ± 0.5% or ±5ºC higher one ± 1 digit

RTD CU50Ω is PV ± 0.5% or ±3ºC higher one ± 1 digit

Environment resistance is rated at no freezing or condensation.

Parts description

1. Present temperature (PV) display (Red)

1) RUN mode: Present temperature (PV) display

2) Parameter setting mode: Parameter display

2. Set temperature (SV) display (Green)

1) RUN mode: Set temperature (SV) display

2) Parameter setting mode: Parameter setting value display

3. Control/Alarm output display lamp

1) AL1/AL2: When AL1, AL2 alarm output ON, this lamp

turns ON.

2) OUT: When control output ON, this lamp turns ON.

During SSRP control output type in CYCLE/PHASE

control, this lamp turns ON when MV is over 3.0%.

4. Auto tuning lamp

AT lamp flashes by every 1 sec during operating auto tuning.

MODE

key

Used when entering into parameter setting group, returning

to RUN mode, moving parameter, and saving setting values.

6. Adjustment

Used when entering into set value change mode, digit

moving and digit up/down.

7. Digital input key

Press

keys for 3 sec. to operate the set function

(RUN/STOP, alarm output reset, auto tuning) in digital input

key [DI-T].

ºC

8. Temperature unit (

/℉) indicator

It shows current temperature unit.

Input sensor and temperature range

Input sensor

Display

Temperature range(

ºC

)

Temperature range(℉)

-50 to 1200

KCaH

K(CA)

KCaL

-50.0 to 999.9

-58.0 to 999.9

JIcH

-30 to 800

J(IC)

JIcL

-30.0 to 800.0

-22.0 to 999.9

LIcH

-40 to 800

Thermorcouple

L(IC)

LIcL

-40.0 to 800.0

TCcH

-50 to 400

T(CC)

TCcL

-50.0 to 400.0

-58.0 to 752.0

R(PR)

RPR

0 to 1700

S(PR)

SPR

0 to 1700

DPtH

-100 to 400

-148 to 752

DPt100Ω

DPtL

-100.0 to 400.0

-148.0 to 752.0

RTD

CUsH

-50 to 200

CU50Ω

CUsL

-50.0 to 200.0

-58.0 to 392.0

Dimensions

TCN4L

1)TCN4S

11.0 X 22.0mm

7.0 X 14.0mm

2)TCN4M

3)TCN4H

Approx. 179g

4)TCN4L

5)Terminal cover(Sold separately)

6)Panel cut-out

Unit

Model

TCN4S

Min. 65

TCN4M

Min. 90

TCN4H

Min. 65

TCN4L

Min. 115

-58 to 2192

Installation

TCN4S(48X48mm) series

Other series

-22 to 1472

-40 to 1472

-40 to 999.9

-58 to 752

32 to 3092

-58 to 392

Insert product into a panel, fasten bracket by pushing with tools as shown above.

[Unit: mm]

Connections

1)TCN4S

Terminal

cover

Terminal

cover

Terminal

cover

Terminal

cover

Flow chart for setting group

1. All Parameter

Run mode

Please any key among

2sec.

MODE

SV setting

Parameter 1group

PAR1

AL1 alarm termerature

AL1

AL2 alarm termerature

AL2

Auto tunung

Proportional band

Integral time

Derivative time

Min. 65

+0.6

-0

Min. 90

+0.7

-0

Min. 115

+0.8

Manual reset

-0

Min. 115

+0.8

REST

-0

Hysteresis

HYS

3sec.

MODE

Press

key over 3 sec in any setting group, it saves the set value and returns to RUN mode.

MODE

(Exception: Press

key once in SV setting group, it returns to RUN mode).

MODE

If no key entered for 30 sec., it returns to RUN mode automatically and the set value of parameter is

not be saved.

Press

key again within 1 sec. after returning to RUN mode, it advances of the ﬁ rst parameter of

MODE

previous setting group.

Press

key to move next parameter.

MODE

Parameter marked in

might not be displayed depending on other parameter settings.

Set parameter as 'Parameter 2group → Parameter 1group → Setting group of set value' order

considering parameter relation of each setting group.

1: It is not displayed for AC/DC power model (TCN4 -22R).

2)TCN4M

B' RTD TC

※2

SOURCE

1: 12VDC±2V 20mA Max.

2: AC power: 100-240VAC 5VA 50/60Hz

AC/DC power: 24VAC 5VA 50/60Hz

24-48VDC 3W

4sec.

MODE

Parameter 2group

PAR2

Input

Temperature

Input

sensor

unit

correction

digital ﬁ lter

IN-T

UNIT

IN-B

MAvF

Control output

SV high-

SV low-limit

Control type

operation

limit value

value

C-MD

O-FT

H-SV

L-SV

Control output

SSRP output

Control

AL1 alarm

※1

type

method

cycle

operation mode

OUT

SSrM

AL-1

LBA

Alarm output

AL2 alarm

LBA detection

monitoring time

hysteresis

operation mode

band

LBaT

AHYS

AL-2

LBaB

Digital input

Control output MV in case

key

of input break error

Lock setting

DI-K

ErMV

LOC

3sec.

MODE