DYNAPAR HS20 Series 기술 게시판
{카테고리_이름} DYNAPAR HS20 Series에 대한 기술 게시판을 온라인으로 검색하거나 PDF를 다운로드하세요. DYNAPAR HS20 Series 4 페이지. Sealed hollow shaft
페이지 인쇄Dynapar brand Encoder
Series HS20 Sealed Hollow Shaft
Technical Bulletin
DESCRIPTION
The Dynapar brand Series HS20 Sealed
Hollowshaft encoder is designed for easy
installation on motor or machine shafts. Its
hollowshaft design eliminates the need for a
flexible shaft coupling, mounting bracket,
flower pot, or flange adapter. This not only
reduces the installation depth, but also lowers
total cost.
The Series HS20 Sealed Hollowshaft's floating
shaft mount and spring tether minimize
bearing loads and eliminate flexible shaft
couplings to reduce wear and maintenance.
SPECIFICATIONS
STANDARD OPERATING CHARACTERISTICS
Code: Incremental
Resolution: 50 to 2540 PPR (pulses/
revolution)
Accuracy: (worst case any edge to any
other edge) <1024 PPR (metal disk): ±7.5
arc-min.
≥1024 PPR (glass disk): ±2.5 arc-min.
Format: Two channel quadrature (AB) with
optional Index (Z) and complementary
outputs
Phase Sense: A leads B for CCW shaft
rotation viewing the hub clamp end of the
encoder
Quadrature Phasing: 90° ± 22.5°
electrical
Symmetry: 180° ±18° electrical
Index: 180° +18°/-135° electrical (gated
with B low)
Waveforms: Squarewave with rise and fall
times less than 1 microsecond into a load
capacitance of 1000 pf
ELECTRICAL
Input Power:
5 to 26 VDC at 100 mA max., not including
output loads
Outputs:
7273 Open Collector: 30 VDC max., 40 mA
sink max.
7272 Push-Pull and Differential Line
Driver: 40 mA sink or source
Bulletin Number: 702375-0001
Revision Level: J
Date: July 27, 2014
1675 Delany Road
Gurnee, IL 60031-1282
Phone: 847.662.2666
Fax: 847.662.4150
Application Assistance 1.800.234.8731
Frequency Response:
75 kHz min. for extended temperature range)
Electrical Protection: Overvoltage, reverse
voltage and output short circuit protected
Noise Immunity: Tested to EN61326-1 EMC
(Heavy Industrial) for Electro Static Discharge,
Radio Frequency Interference, Electrical Fast
Transients, Conducted and Magnetic Interfer-
ence
Mating Connector:
6 pin, style MS3106A-14S-6S (MCN-N4);
7 pin, style MS3106A-16S-1S (MCN-N5);
10 pin, style MS3106A-18-1S (MCN-N6);
5 pin, style M12: Cable with connector available
8 pin, style M12: Cable with connector available
MECHANICAL
Bearing Life: (at maximum tether loading)
Standard tether: 5x10
Slotted tether: 8x10
Shaft Speed: 6000 RPM max.
Shaft Bore Tolerance: Nominal +0.0002"/
+0.0008" (+0.005/+0.020 mm)
Mating Shaft Requirements:
Runout: ±0.005" (±0.13mm) radial, max.
Endplay: ±0.050" (±1.27 mm) axial, max.
Length: 0.80" (20 mm), minimum
Starting Torque: 3.0 oz-in max.
Moment of Inertia: 5.1 x 10
Weight: 10 oz. max.
ENVIRONMENTAL
Operating Temperature:
Standard: 0 to +70° C
Extended: 0 to +85 °C (consult factory for low
temperature operation to –40 °C)
Storage Temperature: –40 to +85° C
Shock: 50 G's for 11 milliseconds duration
Vibration: 5 to 2000 Hz at 2.5 G's
Humidity: to 98% without condensation
Enclosure Rating: NEMA4/IP65 (dust proof,
washdown)
100 kHz min. (index
9
revolutions
9
revolutions
-4
oz–in–sec
2