Autonics LE4SA 지침 - 페이지 13
{카테고리_이름} Autonics LE4SA에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics LE4SA 18 페이지. Din w48xh48mm digital backlight lcd timer
Autonics LE4SA에 대해서도 마찬가지입니다: 매뉴얼 (17 페이지)
페이지 인쇄
LE4S Series
LE4S Output operation mode
Mode
Time chart
[
INT
]
INT
Interval
1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. When RESET signal is ON, display value and output will be reset.(① position)
T > Ta
4. If RESET signal is OFF when START signal is ON,"STEP 1" will be restarted.
5. When START signal is OFF, display value and output will be reset.(② position)
INt1
[
]
INTⅠ
Interval 1
1. Output will be ON when START signal is ON at status of power on and Timing operation starts.
2. Output will be OFF when timing operation is progressed up to the setting time. Display value will be HOLD.
3. Even though START signal is applied repeatedly, only the initial signal is recognized.(① position)
4. If START signal is ON after timing operation is progressed up to the setting time, Output will be ON and setting
T > Ta
5. When RESET signal is ON, display value and output will be reset.(② position)
[
NFD
]
ON OFF D
ON-OFF Delay
1. If START signal is ON when power is on, Output will be ON when timing operation is progressed up to the Ton
2. If START signal is applied repeatedly, output is ON and display value will be reset.(① position)
3. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START
T > Ta
4. It is able to set each Toff time and Ton time separately.
NFd1
[
]
ON OFF DⅠ
ON-OFF Delay 1
1. If START signal is ON when power is on, timing operation starts. Output will be ON when timing operation
2. Output will be ON when START signal is ON and goes OFF during setting time and display value will be reset.(① position)
3. Output will be OFF when START signal is OFF and goes ON during setting time and display value will be reset.(① position)
4. When RESET signal is ON, display value and output will be reset. When RESET signal is OFF while START
T > Ta
5. It is able to set each Toff time and Ton time separately.
[
OFD
]
OFF D
OFF Delay
1. If START signal is ON when power is on, output will be ON.
2. When START signal is OFF, timing operation starts. Output will be OFF when timing operation is progressed up
T > Ta
3. When RESET signal is ON, display value and output will be reset.
※ Initial status : UP mode-display value is "0", output is "OFF". DOWN mode-display value is "setting time", output is "OFF".
K-32
T
POWER
START
RESET
RELAY OUT
Set time
UP
0
Set time
DOWN
0
T
POWER
START
①
RESET
RELAY OUT
Set time
UP
0
Set time
DOWN
0
time will be reset and then timing setting starts.
Ton
Toff
POWER
START
RESET
RELAY OUT
Toff
Ton
UP
0
Toff
Ton
DOWN
0
setting time(On-Delay). IF START signal is OFF, output will be ON when timing operation is progressed up to
the Toff setting time (OFF-Delay).
signal is ON, it will be operating as On-Delay.(② position)
Ton
Toff
POWER
START
RESET
RELAY OUT
Toff
Ton
UP
0
Toff
Ton
DOWN
0
is progressed up to the Ton setting time(On-Delay). IF START signal is OFF, output will be ON when timing
operation is progressed up to the Toff setting time (OFF-Delay).
signal is ON, it will be operating as On-Delay.(② position)
Ta
POWER
START
RESET
RELAY OUT
Set time
UP
0
Set time
DOWN
0
to the setting time. Display value will be HOLD.
T
Ta
②
①
Ta
T
T
Ta Ta
Toff
Ta
Ton
①
②
Ta Ta
Toff
Ta
Ton
①
②
T
Ta
T = Setting time, T > Ta
Operation
T
POWER
START
RELAY
T = set time
T
②
POWER
START
RELAY
T = set time
Ta
Ton
Toff
POWER
START
RELAY
OUT
Ton, Toff = set time
Ta
Ton
Toff
POWER
START
RELAY
OUT
Ton, Toff = set time
Ta
T
POWER
START
RELAY
OUT
T = set time
T
OUT
T
T
OUT
Ton
Toff
Ton
Toff
T