Autonics BJR DDT Series 제품 설명서

{카테고리_이름} Autonics BJR DDT Series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics BJR DDT Series 5 페이지. Oil-resistant photoelectric sensors

페이지 인쇄

TCD210044AB

Oil-resistant

Photoelectric Sensors

BJR Series

PRODUCT MANUAL

For your safety, read and follow the considerations written in the instruction

manual, other manuals and Autonics website.

The specifications, dimensions, etc. are subject to change without notice for product

improvement. Some models may be discontinued without notice.

Features

• Long sensing distance with lens of high performance

: Through-beam type 15 m, diffuse reflective type 1 m,

polarized retroreflective type 3 m (MS-2S)

• M.S.R. (Mirror Surface Rejection) function (Polarized retroreflective type)

• Compact size : W 11 × H 32 × L 20 mm

• Light ON/Dark ON operation mode switch

• Built-in sensitivity adjustment adjuster

• Reverse power protection circuit and output short overcurrent protection circuit

• Mutual interference prevention function (except through-beam type)

• Excellent noise immunity and minimal influence from ambient light

• Stronger in the environment with full of cutting fluid or lubricating oil

(optimized for automobile and machine tool industry)

• IP67 protection rating (IEC standard),

IP67G oil resistance protection rating (JEM standard)

ᜢ ᜽ ᜫ

Safety Considerations

• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.

• ᜸ symbol indicates caution due to special circumstances in which hazards may occur.

᜸ Warning

Failure to follow instructions may result in serious injury or death.

01. Fail-safe device must be installed when using the unit with machinery that

may cause serious injury or substantial economic loss. (e.g., nuclear power

control, medical equipment, ships, vehicles, railways, aircraft, combustion

apparatus, safety equipment, crime/disaster prevention devices, etc.)

Failure to follow this instruction may result in personal injury, economic loss or fire.

02. Do not use the unit in the place where flammable/explosive/corrosive gas,

high humidity, direct sunlight, radiant heat, vibration, impact or salinity

may be present.

Failure to follow this instruction may result in explosion or fire.

03. Do not disassemble or modify the unit.

Failure to follow this instruction may result in fire.

04. Do not connect, repair, or inspect the unit while connected to a power

source.

Failure to follow this instruction may result in fire.

05. Check 'Connections' before wiring.

Failure to follow this instruction may result in fire.

᜸ Caution

Failure to follow instructions may result in injury or product damage.

01. Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or product damage.

02. Use a dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in fire.

Cautions during Use

• Follow instructions in 'Cautions during Use' . Otherwise, It may cause unexpected

accidents.

• When connecting an inductive load such as DC relay or solenoid valve to the output,

remove surge by using diodes or varistors.

• Use the product after 0.5 sec of the power input.

When using a separate power supply for the sensor and load, supply power to the

sensor first.

• The power supply should be insulated and limited voltage/current or Class 2, SELV

power supply device.

• Wire as short as possible and keep it away from high voltage lines or power lines to

prevent surge and inductive noise.

• When using switching mode power supply (SMPS), ground F.G. terminal and connect

a condenser between 0V and F.G. terminal to remove noise.

• When using a sensor with a noise-generating equipment (e.g., switching regulator,

inverter, and servo motor), ground F.G. terminal of the equipment.

• This unit may be used in the following environments.

- Indoors (in the environment condition rated in 'Specifications')

- Altitude max. 2,000 m

- Pollution degree 3

- Installation category II

Product Components

Sensing type

Through-beam

Product components Product, instruction manual

Reflector

Adjustment screwdriver × 1

Bracket A

× 2

M3 bolt

× 4

Polarized retroreflective

Diffuse reflective

MS-2S

× 1

× 2