dynarex 10443 사용자 설명서 - 페이지 4
{카테고리_이름} dynarex 10443에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. dynarex 10443 4 페이지. Air mattress with digital pump
페이지 인쇄
STORAGE
1. Switch off power from main and unplug,
separate the pump from the mattress and
place the mattress flat.
2. Fold the mattress in two from mattress foot
to head.
3. Allow time for air to escape from mattress
to reduce storage space.
4. Close the protective cap cover on the
quick connector.
SPARE PARTS/ACCESSORIES
For spare parts and accessories please
contact Dynarex or an authorized dealer.
GENERAL CONDITIONS OF DISPOSAL
Dispose the device in the appropriate
disposal areas for recycling.
At the end of its life, the products must not be
disposed of along with other domestic waste.
Dispose this equipment by bringing it to a
specific recycling point for electric and
electronic equipment or others that provide
this service.
TROUBLESHOOTING
If your questions can't be answered with
below information, please contact your local
agent directly. They might require a
technician to take care of the problem.
Check control unit is connect to the mains power supply and that
No lights on unit
the unit is switched on.
Check quick blow fuse on the control unit or mains plug fuse.
Check main power to the control unit and that the plug is switched.
Check mattress air supply connector is connected to the pump
unit correctly.
Low pressure alert
Check CPR connector is connected properly.
Under the mattress cover check all "T" & "L" connectors are
connected to the air tubes.
Check the connector tubes for kinks, crimps or damage.
Patient's body is sagging
Increase the value of the comfort the setting. Wait a couple of
in the middle/bottoming
minutes so pressure can stabilize before making another change.
out
Control lock up
Turn the control unit off and unplug the pump. Wait a few minutes
or "freeze"
and plug the control unit back in. Turn on the control unit.
MAINTENANCE
In case of repair, use only original spare
parts and accessories.
CLEANING AND DISINFECTION
WARNING!
Unplug the pump before starting
the cleaning procedure.
1. Clean the mattress with mild soap.
2. Do not immerse or soak pump unit.
3. After cleaning, dry the mattress without
direct sunlight exposure.
4. Check that the connection tubes are not
obstructed by dust or other object. Use a
soft swab to clean the tubes if necessary.
NOTE:
Never use acids, alkalis or solvents such
as acetone to clean the mattress.
5
TECHNICAL FEATURES
Pump Control Unit
FEATURE
PUMP
Power supply
1
20 V / 60 H z
Power
15.5 W
Fuse rating
1A / 250 V
Pressure
20 mmhg~60 mmhg
Dimensions
12½" (W) × 12" (L) × 6" (H)
Cycle
10/15/20/25 mins
Operation: +10˚C / +40˚C
Environment
Storage: -15˚C / +50˚C
Temperature
Shipping: -15˚C / +70˚C
Operation: 10%-90%
Environment
Storage: 10%-90% non-condensing
Humidity
Shipping: 10%-90% non-condensing
Atmospheric Pressure
Operation: 700-1013, 25 hPa
Mattress
FEATURE
MATTRESS
10443-80" (L) × 36" (W) × 8" (H)
Dimensions
10444-80" (L) × 36" (W) × 8" + 3" perimeter (H)
Cell height (inflated)
8"
Air cell material
Nylon/TPU
Cover material
PU + Fiber Quilting
Elements number
20 cells
Max weight
450 lb.
Weight
25 lb.
6