Autonics ARD-A Series 제품 설명서 - 페이지 3

{카테고리_이름} Autonics ARD-A Series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics ARD-A Series 4 페이지. Devicenet remote i/o analog, terminal block type
Autonics ARD-A Series에 대해서도 마찬가지입니다: 매뉴얼 (10 페이지)

페이지 인쇄

DIP Switch Setting

• The input/output range can be set via the DIP switch. However, CH0 - CH1 / CH2 - CH3

cannot be set separately.

• SW7: Not used

SW8: [ON] DIP switch setting

[OFF] communication setting (each channel)

• ON: ■ / OFF: □

■ ARD-AI04

Max. allowable

No. Input range

input range

0 to 5 VDCᜡ

-0.25 to 5.25 VDCᜡ

1 to 5 VDCᜡ

0.8 to 5.2 VDCᜡ

0 to 10 VDCᜡ

-0.5 to 10.5 VDCᜡ

-5 to 5 VDCᜡ

-5.5 to 5.5 VDCᜡ

-10 to 10 VDCᜡ -11 to 11 VDCᜡ

DC 4 to 20 mA

DC 3.2 to 20.8 mA

DC 0 to 20 mA

DC 0 to 21 mA

■ ARD-AO04

Max. allowable

No. Output range

output range

0 to 5 VDCᜡ

-0.25 to 5.25 VDCᜡ

1 to 5 VDCᜡ

0.8 to 5.2 VDCᜡ

0 to 10 VDCᜡ

-0.5 to 10.5 VDCᜡ

-5 to 5 VDCᜡ

-5.5 to 5.5 VDCᜡ

-10 to 10 VDCᜡ -11 to 11 VDCᜡ

DC 4 to 20 mA

DC 3.2 to 20.8 mA

DC 0 to 20 mA

DC 0 to 21 mA

Specifications

Model

ARD-AI04

Power supply

Rated voltage: 24 VDCᜡ, voltage range: 12-28 VDCᜡ

Power consumption

≤ 3 W

Input 4-point

Output points

(switchable voltage/current)

0-10 VDCᜡ, -10-10 VDCᜡ,

Voltage

0-5 VDCᜡ, 1-5 VDCᜡ, -5-5 VDCᜡ

(input impedance: ≥ 1 MΩ)

DC 4-20 mA, DC 0-20 mA

Current

Control

(input impedance: 250 Ω)

I/O

Max. allowable I/O ± 5 % F.S. of I/O range

Resolution

14 bits, 1/16,000

At room temperature (25 ℃ ± 5 ℃) range: ± 0.3 % F.S.

Accuracy

Out of room temperature range: ± 0.6 % F.S.

I/O Slave messaging (group 2 only slave)

Communication spec.

: supporting Poll command, Bit_strobe command, Cyclic command,

COS command

Communication speed

125 kbps (≤ 500 m), 250 kbps (≤ 250 m), 500 kbps (≤ 100 m)

(comm. distance)

Protocol

DeviceNet

I/O and internal circuit: non-insulation,

Insulation method

DeviceNet and internal circuit: insulation, DeviceNet power: insulation

Insulation resistance

≥ 200 MΩ ( 500 VDCᜡ megger)

Noise immunity

± 500 VDCᜡ the square wave noise (pulse width: 1 ㎲) by the noise simulator

500 VACᜠ at 50/60 Hz for 1 min (between external terminals and case,

Dielectric strength

between output terminals and power terminals)

1.5 mm amplitude at frequency 10 to 55 Hz (for 1 min) in each X, Y, Z

Vibration

direction for 2 hours

Shock

500 m/s

(≈ 50 G) in each X, Y, Z direction for 3 times

Ambient temperature

-10 to 50 ℃, storage: -25 to 75 ℃ (no freezing or condensation)

Ambient humidity

35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)

Protection rating

IP20 (IEC standard)

Protection circuit

Surge and ESD protection, reverse power protection circuit

Indicator

Network status (NS) and unit status (MS) indicator (green, red LED)

Material

Front and body case: PC

Mounting method

DIN rail or panel mounting

Approval

ᜢ ᜣ ᜫ

Unit weight (packaged)

≈ 145 g (≈ 210 g)

1 2 3 4 5 6 7 8

CH0, CH1

CH2, CH3

SW1

SW2

SW3

SW4

SW5

SW6

□

■

□

■

□

■

□

■

□

■

□

■

□

■

□

■

□

■

□

■

CH0, CH1

CH2, CH3

SW1

SW2

SW3

SW4

SW5

SW6

□

■

□

■

□

Not used

■

□

■

□

Not used

■

□

ARD-AO04

Output 4-point

(voltage 2 CH, current 2 CH)

0-10 VDCᜡ, -10-10 VDCᜡ,

0-5 VDCᜡ, 1-5 VDCᜡ, -5-5 VDCᜡ

(load resistance: ≥ 1 kΩ)

DC 4-20 mA, DC 0-20 mA

(load resistance: ≤ 600 Ω)

ᜢ ᜣ ᜫ DeviceNet compatible

≈ 145 g (≈ 210 g)

I/O Circuit Diagram

Network

Type

connector

V+

CAN_H

SHIELD

Analog

CAN_L

input

V-

□

V+

□

CAN_H

□

SHIELD

Analog

CAN_L

output

□

V-

■

Function

Com. speed auto-recognition

Network power voltage monitoring

Basic

Unit power on total time monitoring

Unit comment

Last maintenance data stored

□

Scaling

I/O comment

Adjustment gradient

Adjustment offset

Input conversion points setting

Analog

Input digital filter

Peak/Bottom Hold

Disconnected cable detection

Input comparison

Hysteresis

Output setting for error

■ Communication speed auto-recognition

• It recognizes communication speed when connecting master. Communication speed is

able to change only from master unit. After changing communication speed, re-supply the

network power to apply the changed communication speed.

■ Network power voltage monitoring

• If network power voltage is lower than the set value, the network power voltage drop flag bit

of Status bit is ON. It can be read by Configurator or Explicit message.

• Set monitoring voltage by Explicit message at Network Power voltage (set value) of

Application Object.

• Setting range: 0 to 255 (factory default: 12 V, allowable range: ± 1 V)

• Min. supplied power is 12 V for ARD unit. If network voltage is lower than 12 V, the contents of

Explicit message reading is not guaranteed.

■ Unit power on total time monitoring

• When total time for supplying power to the unit becomes the SV, Threshold Run Hours Flag

bit of Status Bit turns ON. It can be read by Configurator or Explicit message.

• Set the time by Explicit message at Threshold Run Hour of Application Object.

• Setting range: 0 to 429,496,729 hours (factory default: 876,000 hours),

measured unit: 0.1 hours (6 minutes)

■ Unit comment

• You can set the comments for the unit (product description) on network. It can be read by

Configurator or Explicit message.

• Set comment by Explicit message at Unit Comment of Application Object.

• Setting range: max. 32 characters

■ Last maintenance date

• It saves the last date of maintenance. It can be read/ written by Configurator or Explicit

message.

• Set maintenance date by Explicit message at I/O Last Maintenance Data Setting of Analog

Input Point Object.

• Data: 0x07DB020E→07DB (2011), 02 (February, 0E (14th)

■ Input conversion points setting

• Conversion cycle is changed by the number of points (point, channel). (conversion cycle:

1 ms/point, when using 4 points, it is 4 ms). It can be read/written by Configurator or Explicit

message.

• After changing the number of conversion points, re-supply the network power.

• Set the number of conversion points by Explicit message at Number of AD Conversion

Points Setting of Analog Input Point Object.

• Setting range: 1 to 4 points (factory default: 4 points), conversion cycle: 1 ms/1 point

Internal circuit

Input circuit

Power circuit

Analog

GND

V.OUT

Internal circuit

Output circuit

Power circuit

Analog

GND

ARD-AI04

ARD-AO04

●

External

connections

Load

≤ 1 kΩ

COM

I.OUT

Load

COM

≤ 600 Ω

●