Gallo Tech GTS-3RS 작동 및 설치 매뉴얼 - 페이지 12

{카테고리_이름} Gallo Tech GTS-3RS에 대한 작동 및 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gallo Tech GTS-3RS 16 페이지. Keyless rfid push button start & security system

페이지 인쇄

1. Installation Instructions

Installing Connector C3:

22 Pin (Black) Wire Harness (Main Harness)

See Figure 1 for pin number and location.

Pin 1. (RED) Parking Light Pwr. w/15A fuse Used to power the parking lights. Connect this wire to Bat + 12v.

Pin 2. (Yellow) Parking Lights Out (+). Connect to the vehicles parking light circuit. If parking lights require more

than 10 amps (not normal) use an external 30 Amp relay.

Pin 3. (Blue/Red) NC-2 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock system.

Pin 4. (Blue/White) Com-2 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock system.

Pin 5. (Blue/Yellow) NO-2 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock system.

Pin 6. (Green/Red) NC-1 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock system.

Pin 7. (Green/White) Com-1 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock

system.

Pin 8. (Green/Yellow) NO-1 Used for central door locks. See Figure 2, 3, 4, 5, 6 for your vehicle's door lock system.

Pin 9. (Purple) Trunk output (-). Trunk Release Output Neg. (-). Connect to the trunk release Neg. (-) trigger wire

on the vehicle's trunk release relay. In the event that a trunk release is to be added to the vehicle, an additional relay

and trunk release solenoid will be required.

Pin 10. (White/Black) Arm Output (-) Is a neg. (-) output when the alarm is triggered. Can be used to activate other

alarm triggered devices. (125 ma max.)

Pin 11. (White/Blue) Auxiliary output (-) This is a low current (-) output (125ma max). It can be used to activate the

(-) neg side of a relay that may be used for operating the passenger door of a shaved door vehicle, an extra trunk

release or an electric window close operation. Connect to a window close module (not included) with a Neg. (-)

input. Follow the window close module instructions for wiring to window motors. Do not connect this wire directly to

the vehicle's window close switch. The output duration can be either 2 sec or 15 sec per Table #1 option 8, page 9.

Pin 12. (RED) Module Power. w/5A fuse Used to power the GTS-3RS Control Module. Connect this wire to Bat +

12v.

Pin 13. (White) Ignition 2 output (-) Used to activate an additional relay so that an IGN 2 circuit may be used when

the vehicle requires its use. Not all vehicles require an IGN 2 circuit. Pin4 must be connected to the (-) neg terminal

of the relay. See Figure 1, option 2.

Pin 14. (Purple/White) Start Enable input (-) input. Connect to a good chassis ground (-).

Pin 15. (Black) Ground (-) Connect to a good chassis ground (-).

Pin 16. (Orange/White) Handbrake (-). Connect to the handbrake switch that is neg (-) when handbrake is set.

Pin 17. (White/Red) Disarm Output (-) Ground While Running (GWR). Connect to the Neg (-) input of a security

bypass device. These devices are used in the event that the vehicle has an OEM security system that prevents

starting the vehicle without the security key. The proper security by-pass module for the specific vehicle can be

found at www.gallotech.com/support. Follow the instruction that came with the by-pass module.

This wire is activated only during engine starting and running. When the engine is turned OFF there will be no GWR

output.

Pin 18. (Black/White) Foot Brake input (+) (+12v) Foot Brake Switch Input Used for auto door lock function and

Starting. Connect to Foot brake switch terminal that has +12v only when foot brake is depressed.

Pin 19. (Brown/Black) Door (+) input. Pos. (+) Door Switch Input. Connect to a Pos. (+) Door Trigger switch. If

the vehicle has "-" Neg. Door Trigger use the (Brown/White, Pin 18) wire instead. Tape or wire nut wire if not used.

Pin 20. (Brown/White) Door (-) input. Neg. (-) Door Trigger switch Input. Connect to the Neg. (-) Door Trigger

switch. If the vehicle has "+" Pos Door Trigger, use the (Brown/Black), Pin 16) wire instead. Tape or wire nut wire if

not used.

Pin 21. (Light Blue) Tach Input. Before connecting see Sec 1.4 "Voltage/ Tach signal detection

Options".

Pin 22. (Brown) Siren/Horn output (+). +12v Output. Connect to the RED Siren wire. Connect the second siren

(Black) wire to a good chassis ground. If the vehicle's horn is used; connect Pin 22 (Brown) wire to the (+) pos

terminal on the horn relay. Do not connect directly to the horn. Table #1 option 10 must be changed to either Siren

or Horn.

- 12 -

061515V54RS