Majestic Appliances MJ-9000V 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Majestic Appliances MJ-9000V에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Majestic Appliances MJ-9000V 20 페이지. Majestic appliances owners manual front-load washer mj-9000v, mj-9000vg
Majestic Appliances MJ-9000V에 대해서도 마찬가지입니다: 설치 매뉴얼 (6 페이지), 소유자 매뉴얼 (18 페이지)

페이지 인쇄

Installing/Removing

Getting things ready to install your

appliance (continued)

Plumbing - Water, Drains

WATER CONNECTION

1. This appliance can be used with either hot/cold or cold/cold connections.

2. The hoses supplied have either a straight end or an elbow end. The elbow

end is meant to connect to the washer. Be sure to connect the hot hose to

the hot side of the appliance itself, the cold side to the cold connection.

(See picture) The straight end to the 3/4" BSP standard hose bib thread.

3. MAKE SURE WASHERS ARE INSTALLED IN EACH END OF THE SUPPLY

HOSES.

4. Ensure that water connections are free from debris or sediment.

6. BRASS PRESSURE REDUCERS MUST BE INSTALLED TO PROTECT

COMPONENTS INSIDE THE APPLIANCE.IMPORTANT ! CHECK THREADS

ON THE MACHINE, THE BRASS PRESSURE REDUCERS AND THE SUPPLY

HOSES TO ENSURE THEY ARE CLEAN. DO NOT USE EXCESSIVE FORCES.

TIGHTEN BY HAND. DO NOT USE POWER TOOLS.

Connection of the drain hose to standpipe

• Outlet end of drain hose (See figure 2) must be at least 20" above bottom of washer. Do NOT block top of standpipe closes with tape

or other materials. An air break must be provided at the standpipe to avoid siphoning.

• Connect the drain hose to a standpipe (with internal diameter of at least 3.2 cm or 1 1/4" min. diameter) with a minimum carry away

volume of 7 gallons. The top of the standpipe must be 20" minimum from the botton of the appliance. Place drain hose for drainage into

a sink tub or standpipe, ensuring that there are no kinks or bends. The free end must be at a height of 80 cm (31 1/2") from the floor,

the hose must be fixed in the appropriate hook on the upper part of the back panel (fig.4)

DO NOT INSERT THE END IF THE DRAIN HOSE MORE THAN 6" INTO

THE STANDPIPE. INSERTING MORE MAY CAUSE THE APPLIANCES TO

HAVE INSUFFICIENT DRAINAGE.

Exhaust Duct Installation

• Check that all ducting is lint free. Secure ducting with clamps or metal

tape.

• The exhaust duct must end with an approved exhaust vent hood with

swing out dampers or appropriate louvers.

• Flex or rigid metalic ducting is recommended.

• Exhaust duct should be short and straight and slope downwards and

away from the appliance. Long exhaust duct runs can increase drying

time and collect lint.

IMPORTANT! THE EXHAUST DUCT SHOULD NOT BE INSERTED INTO A

CHIMNEY WALL, CEILING OR CONCEALED SPACE OR STRUCTURE.

CORRECT LEVELING OF UNIT IS

ESSENTIAL

It is important for the machine to be

perfectly level. The angle of inclination on

the work surface must not be more than

2 degrees. For this reason the machine is

fitted with adjustable feet used for leveling

the machine before use. In the case of

carpeted flooring, remember to check that

the ventilation in the support area is not

plugged.