Centurion RDO-10A 설치 지침 및 사용자 설명서 - 페이지 7

{카테고리_이름} Centurion RDO-10A에 대한 설치 지침 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Centurion RDO-10A 13 페이지. Roller door opener

페이지 인쇄

Forced Learn

May be initiated by long press of;

 Learn Button (Fig.6‐A or 7‐A) for 3 sec, or

 Button 4 of a Mass Learned transmitter

– Light will paused single blink once Opener has entered

Forced Learn Mode

 Repeatedly cycle the opener

– Light will extinguish once learning is complete

M MODE

Description

A less sensitive Safety Reverse system more suited for use

suited for use on large, heavy or badly worn doors.

Function

Features conventional one time force adjustment – during a

closing movement the Opener will stop and commence to

Safety Reverse upon encountering an obstruction.

Enabling

 Switch power off at power outlet

 Remove the light cover

 Select Dip 1 (Fig.7‐G) to the "OFF" position

Adjustment

 Long Press Learn Button (Fig.7‐A) ‐ Light (Fig.7‐I) paused 2 x

blink – force adjustment can only be carried out while the

Light is blinking

 Open Direction ‐ turn the Green "Open" adjust pin (Fig.7‐C)

to adjust open direction Safety Stop value – clockwise to

increase force, anti‐clockwise to decrease force

 Close Direction ‐ turn the Red "Close" adjust pin (Fig.7‐D)

to adjust close direction Safety Reverse value – clockwise to

increase force and anti‐clockwise to decrease force

 Momentarily press "Learn" Button to close out the

adjustment mode

14. Auto Close

Function

Auto Close automatically closes the door; either 5 sec after a

car has passed through the doorway or after 30 sec if a car

has not passed through the doorway.

15. Courtesy Light

Function

The Courtesy Light;

– provides garage illumination and opener status indication

– will illuminate automatically each time the Opener is

activated and will switch off 90 sec after the last

activation

– may be switched on and off via button 3 of a bulk learned

transmitter (refer sec.10)

16. Dip Switches

Dip 1 Auto Force Mode

Dip 2

Safety Beams Enabled Safety Beams Disabled

Dip 3

Auto Close Enabled

Dip 4

Door Service Enabled Door Service Disabled

SETTINGS AND ADJUSTMENTS

OFF ON

Manual Force Mode

Auto Close Disabled

Automatic Relearn

An Automatic Re Learn will be initiated immediately

subsequent to either one of the following 3 occurrences;

– Run time deviation becoming excessive, or

– Safety Reverse occurring on 3 consecutive occasions, or

– Safety Stop occurring on 3 consecutive occasions.

During relearn LED (Fig.7‐I) will paused single blink then

extinguish once relearn is complete

Testing Close Direction Force

 Ensure that the garage door is resting firmly against the

ground.

 Open the door and place a 40mm thick block of wood on

the ground under the path of the door.

 Initiate a close movement via transmitter or run button – if

the drive force value is correct the opener will stop and

reverse direction upon encountering the block of wood.

 If too little or too much force is required to make the

opener reverse direction – turn the Red Offset Adjust Pin

(Fig.7‐D) 5 degrees in the appropriate direction – towards

Max to increase force – towards MIN to decrease the

amount of force – and then repeat the test.

Testing Open Direction Force

 During an open movement apply some firm downward

force to the garage door.

 If the Safety Stop value is correct the Opener will stop upon

sensing the resistance.

 If too little or too much force is required to make the

opener stop turn the Green "Offset" Adjust Pin (Fig.7‐C) 5

degrees in the appropriate direction – towards "MAX" to

increase force – towards "MIN" to decrease the amount of

force – and then repeat the test

To Enable

 Select Dips 2 and 3 (Fig.7‐G) to the "ON" position.

– Note ‐ Auto Close will only function when Safety Beams

have been fitted and enabled

Indication

– Slow blink – Learning Force values

– 2 x blink when transmitter is pressed – Safety Beam

malfunction

– 3 x blink during Force learning – door load is excessive

– 4 x blink when transmitter is pressed – Opener has

entered Vacation Mode

Dip 5 Mass Learning

Dip 6

Left Hand Installation

Dip 7 Doors over 2.5m high Doors up to 2.5m high

OFF

Simple Learning

Right Hand Installation