KitchenAid YKESC307 설치 지침 매뉴얼 - 페이지 4

{카테고리_이름} KitchenAid YKESC307에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid YKESC307 9 페이지. 30" electric ranges with self-cleaning thermal/convection oven

페이지 인쇄

Excessive

Weight Hazard

Use two or more people to move and

install range.

Failure to follow this instruction can

result in back or other injury.

BAKED

OTHER

Firmly grasp the range and gently

lay it on its back on the cardboard

corners.

Control panels may vary.

'_]

ull cardboard bottom and shipping

base firmly to remove.

Use an adjustable wrench

to loosen the leveling legs

1-1/2 turns.

'_ Place cardboard or hardboard in

front of range. Stand range back up

onto cardboard or hardboard.

Tip Over Hazard

A child or adult can tip the range and

be killed.

Connect

anti-tip bracket

to rear range

foot.

Reconnect

the anti-tip

bracket, if the

range is moved.

Failure to follow these instructions can

result in death or serious burns to

children

and adults.

Place the anti-tip

bracket template

on the floor in

the cabinet

opening so that

the left edge is

against cabinets

and the top

edge is against

the rear wall,

molding or

cabinet. If

25" (63.5 cm) countertop

over

24" (61 cm) cabinet

_f---

anti-tip

bracket

countertop opening is deeper

template

than 25 inches (63.5 cm),

measure and mark a distance 25 inches

(63.5 cm) in from front of countertop

opening

and align template with mark

(or subtract 25 inches (63.5 cm) from

countertop depth and add the difference to

the 2-1!4-inch (5.7 cm) dimension).

25" (63.5

Counteffop

overnangs

cabinet

side.

A = Difference

between

counterfop

depth

and 25"

(63.5 cm).

bracket

template

slide-in

cutout

shown

If countertop is not flush to the side of

cabinet opening, align the left side of the

template to allow for the countertop

overhang. Tape the range anti-tip bracket

template in place.

Contact

a qualified

floor covering

installer for the best procedure

of drilling

mounting

holes through your type of

floor covering.

Before moving,

slide range onto

cardboard

or hardboard,

To mount anti-tip

bracket to wood

floor, use the anti-

tip bracket

template to mark

where to drill

mounting holes.

Use a drill with a

1/8" (0.3 cm) drill

bit to drill the two

holes. Remove template from floor.

To mount anti-tip

bracket to concrete

ceramic

floor, use the anti-tip bracket

template to mark where to drill mounting

holes. Use a drill with a 3/16" (0.48 cm)

masonry drill bit to drill the two holes.

Remove template from floor. Tap plastic

anchors into mounting holes in floor with

hammer.

Line up holes in anti-tip

"_\

bracket with holes in

floor. Use the screws

provided to fasten

anti-tip bracket

to floor.

NOTE: Anti-tip

bracket must be

mounted

securely

to the sub

floor. Depending on the thickness of your

flooring, longer screws may be necessary to

anchor the bracket to the sub floor. Longer

screws are available from your local

hardware store.

Move range close to cabinet

opening. Make electrical

[] connection. See"Electrical

requirements" and "Electrical

connection," Panel B, for details. "8888"

should appear in the clock display. Refer to

Use and Care Guide for information on

electronic controls.

] Remove cardboard or hardboard

from under range. Carefully move

[] range into final position.

i12.

Press on front of storage drawer and release

to open. Pull open to first stop position. Lift

front of drawer to clear white wheels in

drawer guides. Remove drawer and set it

aside on a protected surface.

Look under range

(a flashlight may

be needed) to check

that left rear leveling

leg is engaged in the

anti-tip bracket. If

leveling leg is not properly engaged, remove

and reposition the anti-tip bracket to insure

that the leveling leg fits properly in the anti-

tip bracket.

[14.1

........

Place rack in

oven. Place level on rack,

first side to side; then front to back. If the

range is not level, pull range forward until the

rear leveling leg is removed from the anti-tip

bracket. Adjust the leveling legs up or down.

Then slide range back into position. Check

that leveling leg is engaged in anti-tip

bracket.

NOTE: Oven must be level for satisfactory

baking conditions.

Insert storage drawer into slide

am rails on sides of drawer opening.

Lift front of drawer slightly and

push firmly to close drawer.

Pushinand

turn each

surface unit

control knob to "HI"

position. Check the

operation of the cooktop

¢%

elements and indicator

lights.

OFF

MED

] Check the operation of the oven

element. Press the "BAKE" pad.

[] "350°F '' will appear in the

temperature display. Press the "START" pad.

"Lo" will appear in the display; then "170°F ''

(when oven reaches 170°F).

The bottom element should glow red and

the indicator light should be on. The upper

element should become hot but not glow

red. As the oven temperature rises, the

temperature

in the display will increase in

5°F increments until the oven reaches the

set temperature.

Press "CANCEL/OFF"

pad.

i Check the operation of the broil

element. Close the oven door.

[] Press the "BROIL' pad. "500°F '' will

appear in the temperature display. Press the

"START" pad.

Look through the oven window. The top

element should glow red. Press the

"CANCEL/OFF"

pad.

To get the most

efficient

use from

your

new electric

range,

read your

KitchenAid

Use and Care Guide.

Keep Installation

Instructions

and

Guide

to the electric

range

for

easy reference.

Panel C