KitchenAid KDFE104DSS 사용자 지침 - 페이지 18

{카테고리_이름} KitchenAid KDFE104DSS에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KDFE104DSS 20 페이지. Front control dishwasher
KitchenAid KDFE104DSS에 대해서도 마찬가지입니다: 사용자 설명서 (17 페이지)

페이지 인쇄

PROBLEM

HARD WATER

(WHITE RESIDUE ON

DISHWASHER INTERIOR OR

GLASSWARE)

ODORS

NOISY

FOOD SOILS REMAIN

ON DISHES

DISHES DIRTY/SUDS IN

DISHWASHER/CYCLE NOT

COMPLETE

SANITIZED LIGHT BLINKING

DAMAGE TO DISHWARE

BLINKING LIGHTS

SOLUTION

NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make it

difficult to achieve good cleaning. A water softener is strongly recommended if your hardness is

15 grains or more. If a water softener is not installed, the following steps may help:

Use a commercial cleaner designed for dishwashers once per month.

Clean the upper and lower filters at least once per month. (See "Cleaning Instructions" in the "Filtration

System" section.)

Always use a rinse aid.

Always use a high-quality, fresh detergent.

Use a detergent booster/water softener additive designed for dishwashers.

NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load until a full load

is ready to run, or use the Top Rack Only option (on some models) for partial loads.

Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an upright

glass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option turned off. Do not

use detergent.

The dishwasher may not be draining properly, see "Water Remains In The Tub/Will Not Drain" in the

"Troubleshooting" section.

NOTES:

Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.

Normal water valve hissing may be heard periodically.

A normal snap sound may be heard when the detergent dispenser opens during the cycle and when

the door is opened at the end of the cycle.

Improper installation will affect noise levels.

Be sure the filters are properly installed.

A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms.

Readjust the dishware and resume the cycle.

Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing

performance (see "Dishwasher Use" section).

Check filter to ensure it is properly installed. Clean it if needed. (See "Cleaning Instructions" in the

"Filtration System" section for details.)

Select the proper cycle and option for the type of soils. The ProWash™ or the Tough cycle with the

ProScrub

(on some models) option can be used for tougher loads.

Be sure the incoming water temperature is at least 120°F (49°C).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and hard

water conditions.

Scrape food from dishes prior to loading (do not prerinse).

If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate

properly or may not fill with water.

Suds can come from:

Using the incorrect type of detergent, such as dish detergent for hand washing dishes, laundry

detergent, or hand soap.

Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.

Using an excessive amount of dishwasher detergent.

Call for service.

If no water was present in the machine at any time during a heated wash cycle, the cycle will end and

the Clean LED will not come on. See "Will Not Fill" in the "Troubleshooting" section.

If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final rinse, or

the temperature for your water heater is set too low. Set your water heater to 120ºF (49°C).

Improper loading can cause dishes to become chipped or damaged. (See specific loading instructions

within this guide.)

Blinking LED's will occur when the cycle is paused or when the cycle has been interrupted by opening

the door. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s), and the

countdown bars on the Cycle Status Display all blink together to indicate that attention is needed. See

"Start or Resume a Cycle" in the "Dishwasher Use" section.

Blinking LED's can also occur when certain errors have been detected. In this case, the Clean/

Complete LED will blink 4 times in a row with a pause in between each set of blinks. When this error

occurs, the controls will lock out and not allow another cycle to be started.

Call for service.