Green R/C Model Airplanes Tiger Moth 사용 설명서 - 페이지 6

{카테고리_이름} Green R/C Model Airplanes Tiger Moth에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Green R/C Model Airplanes Tiger Moth 11 페이지. The unique almost-ready-to-fly scale 1:7 model of great britain's famous wwii training aircraft
Green R/C Model Airplanes Tiger Moth에 대해서도 마찬가지입니다: 사용 설명서 (11 페이지)

페이지 인쇄

Green R/C Model Airplanes Tiger Moth 사용 설명서

Step

Step 3. 3. 3. 3. Mount

Step

Mount

the

Step

Mount the

the main

* * * * Open

Bag

Bag 9# 9# 9# 9# and

Bag

hardware needed. . . .

1) Turn the fuselage up side down again. The wires of the main landing gear assembly may need

spreading to match the fore and the rear slots that are located under the covering.

2) There are holes pre-drilled in the bottom of the fuselage for mounting the main landing gear. You

don't need to cut away the covering in the slots. The gear wire will push the covering into the

slots when you tighten the mounting screws . Leaving the covering in the slots will help keep the

wood from getting oil soaked.

3) Slip the main wheels on the axles and use the four wheel collars (L03) to retain the wheels in

place.

4) Finally, fix the main landing gear assembly in place by tightening the mounting screws (L05) in

the hold-down plates (L04) as shown in Fig. (3).

Step

Step 4. 4. 4. 4. Mounting

Step

Mounting

Mounting the

Mounting

Bag.11#

*Open Bag.11#

Bag.11# to get the tail

Bag.11#

*Open

to get the fin

Bag

Bag 12#

Bag

12#

*Open

Bag

13#

to get the rudder

Bag

Bag 13#

13#

1) Mount the control horns onto the rudder and elevator respectively.

2) Place the tail wheel on the tail gear axle and use one of the wheel collars (L08) to retain it in

place. The other collar is used to prevent the gear from moving upward through the hole in the

tail gear mounting plate (L09)

3) Insert the sharp end of the tail-gear strut into the hole pre-drilled in the fin and apply thin CA to

secure it in the fin.

4) Refer to Fig. (4), mount the tail surfaces along with the tail wheel sub-assembly onto the tail end

of the fuselage by inserting the two long tail-surfaces mounting bolts (T03) into the holes &

tubes pre-built in the fuselage and securely tightening the bolts into the nuts

Thus, the complete tail-surfaces are fixed in place.

main

landing

gear

main landing

landing gear

gear sub-assembly

main

to get the main

main landin

and

10#

and 10#

10#

Fig.

Fig. (4)

(4)

(4) Assembly

Assembly

Assembly of of of of the

1. Elevator

4. Tail gear

7. Tail gear mounting screws

the

the tail

tail surfaces

tail

surfaces

surfaces and

surfaces

and

and the

tail

wheel

tail wheel

tail

wheel (L06), tail

wheel

fin

fin hinged

hinged

hinged with

with

with rudder

with

rudder

control

rudder control

control horns

sub-assembly

landin

gear

assembly

assembly (L01) , , , , main

landin gear

gear assembly

the

the tail-surfaces

tail-surfaces

tail-surfaces and

2. Rudder

5. Tail wheel

8. Tail-surfaces mounting bolt

the

the tail

tail

tail wheel

wheel

tail

gear

tail

tail gear

gear

gear (L07), and other hardware needed

rudder

rudder (T01) and the stabilizer

horns

horns (C01) and elevator

main

wheels

main wheels

wheels (L02) and other

and the

and

the tail

the

tail

tail wheel

tail

wheel

3. Retaining collar

6. Mounting plate

stabilizer

stabilizer hinged

hinged

hinged with

elevator

control

horns

elevator control

control horns

horns (C04).

with

with elevator

with

elevator (T02) . . . .

elevator

nuts

nuts built into the fin.

nuts