decorflame QC212-GBKP 매뉴얼 - 페이지 2
{카테고리_이름} decorflame QC212-GBKP에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. decorflame QC212-GBKP 9 페이지. Electric stove heater
leG ASSemBlY
Before using your unit please install the legs as shown in diagram below.
After completely reading instructions, confirm that all controls on stove are in the
oFF position. Plug the unit into a 15 amp, 120 volt outlet.
oPeRATIoN
Controls and switches are located on the front panel inside the glass door.
I/o: Press this button into the "I" position for main power and flame effect. The
indicator light will turn on.
HeATING: For heat function, press this switch while the o/I switch is in the
"I" position for heat. The indicator light will turn on.
THeRmoSTAT: To adjust the temperature to your individual requirements,
turn the thermostat dial to the right (clockwise) to increase the
temperature and to the left to decrease the temperature. This thermostat
control dial can only be used while the I/o switch and heating switches are
in the "I" position. When the heater reaches the desired temperature, the
heater and heating indicator light will turn off, but the fan will continue to
operate. Adjust this knob to restart the heater.
NoTe: When the I/o switch is turned to the oFF position, all other heater
functions will stop even though the switches may be in the "I" position.
THeRmoSTAT CoNTRol
The heat output is controlled by the thermostat, according to the room
temperature. Set the thermostat dial fully clockwise to the maximum
position initially.
When the room is warm enough, reduce the setting by slowly turning the
thermostat dial anti-clockwise until the heater just clicks oFF. This will then
maintain the room temperature at the desired level.
CAUTIoN:
IF YoU USe THIS HeATeR IN CoNjUNCTIoN WITH A THeRmAl CoNTRol, A PRoGRAm
CoNTRolleR, A TImeR oR ANY oTHeR deVICe THAT SWITCHeS THe HeATeR oN
AUTomATICAllY, RememBeR To oBSeRVe All SAFeTY WARNINGS AT All TImeS. THe
SToVe HeATeR HAS SAFeTY oVeRHeAT PRoTeCTIoN. IF THe oVeRHeAT PRoTeCTIoN
TRIPS, SWITCH oFF All SWITCH BUTToNS ANd WAIT APPRoxImATelY 5 -10 mINUTeS.
IT SHoUld ReSeT AUTomATICAllY oNCe THe UNIT CoolS doWN.
mAINTeNANCe
warNiNG: DiScONNEct POwEr aND UNPlUG tHE POwEr cOrD BEFOrE
attEMPtiNG aNy MaiNtENaNcE Or clEaNiNG tO rEDUcE tHE riSk OF FirE,
ElEctric SHOck Or PErSONal iNJUry. tHE BUlB iN yOUr UNit caN BEcOME
ExtrEMEly HOt.
Allow at least 10 minutes between turning off the unit and removing the light bulb
to avoid accidental burning of the skin.
riSk OF FirE: DO NOt ExcEED tHE rEcOMMENDED BUlB wattaGE.
FlAme eFFeCT
The fire effect is created with the use of a 40 watt B-10 candelabra light bulb with
an e-12 (small) socket base. The light bulb will have to be replaced from time to
time when they burn out.
during normal operation, the stove heater will always give you simulated flame
function. If the intensity of flame suddenly increases, it means that the light bulb is
going to burn out.
Replace the light bulb immediately, according to the instruction. do not operate the
stove heater when the light bulb burns out or without the light bulb.
CHANGING THe lIGHT BUlB
STeP 1: open the door of unit with the handle.
STeP 2: loosen the 2 screws at the front of the log set inside the stove. Carefully
lift the logset up far enough to access the light bulbs. You will find 1 x 40 W
Type B-10 candelabra light bulb with e-12 socket base at the bottom.
STeP 3: Replace the burned out light bulb using a new 40 watt Type B-10 candelabra
light bulb.
STeP 4: Reinstall the logset.
STeP 5: Plug in the unit.
CleANING
To clean unit, first turn off the controls on the unit and unplug the unit from
power source.
To clean glass door; remove dust with clean dry cloth or to remove finger prints and
other marks clean glass with clean damp cloth. do not use abrasive cleaners
or spray liquids on the glass door surface.
metal and metal painted parts should be cleaned with a damp cloth. do not use
abrasive cleaners or spray liquids on these surfaces.
SToRAGe
When the heater is not in use, the heater should be stored in a dry location, away
from possible damage. The power cord should be stored properly to avoid contact
with hot or sharp objects.
2