decorflame QC212-GBKP Handmatig - Pagina 2

Blader online of download pdf Handmatig voor {categorie_naam} decorflame QC212-GBKP. decorflame QC212-GBKP 9 pagina's. Electric stove heater

Pagina afdrukken

leG ASSemBlY

Before using your unit please install the legs as shown in diagram below.

After completely reading instructions, confirm that all controls on stove are in the

oFF position. Plug the unit into a 15 amp, 120 volt outlet.

oPeRATIoN

Controls and switches are located on the front panel inside the glass door.

I/o: Press this button into the "I" position for main power and flame effect. The

indicator light will turn on.

HeATING: For heat function, press this switch while the o/I switch is in the

"I" position for heat. The indicator light will turn on.

THeRmoSTAT: To adjust the temperature to your individual requirements,

turn the thermostat dial to the right (clockwise) to increase the

temperature and to the left to decrease the temperature. This thermostat

control dial can only be used while the I/o switch and heating switches are

in the "I" position. When the heater reaches the desired temperature, the

heater and heating indicator light will turn off, but the fan will continue to

operate. Adjust this knob to restart the heater.

NoTe: When the I/o switch is turned to the oFF position, all other heater

functions will stop even though the switches may be in the "I" position.

THeRmoSTAT CoNTRol

The heat output is controlled by the thermostat, according to the room

temperature. Set the thermostat dial fully clockwise to the maximum

position initially.

When the room is warm enough, reduce the setting by slowly turning the

thermostat dial anti-clockwise until the heater just clicks oFF. This will then

maintain the room temperature at the desired level.

CAUTIoN:

IF YoU USe THIS HeATeR IN CoNjUNCTIoN WITH A THeRmAl CoNTRol, A PRoGRAm

CoNTRolleR, A TImeR oR ANY oTHeR deVICe THAT SWITCHeS THe HeATeR oN

AUTomATICAllY, RememBeR To oBSeRVe All SAFeTY WARNINGS AT All TImeS. THe

SToVe HeATeR HAS SAFeTY oVeRHeAT PRoTeCTIoN. IF THe oVeRHeAT PRoTeCTIoN

TRIPS, SWITCH oFF All SWITCH BUTToNS ANd WAIT APPRoxImATelY 5 -10 mINUTeS.

IT SHoUld ReSeT AUTomATICAllY oNCe THe UNIT CoolS doWN.

mAINTeNANCe

warNiNG: DiScONNEct POwEr aND UNPlUG tHE POwEr cOrD BEFOrE

attEMPtiNG aNy MaiNtENaNcE Or clEaNiNG tO rEDUcE tHE riSk OF FirE,

ElEctric SHOck Or PErSONal iNJUry. tHE BUlB iN yOUr UNit caN BEcOME

ExtrEMEly HOt.

Allow at least 10 minutes between turning off the unit and removing the light bulb

to avoid accidental burning of the skin.

riSk OF FirE: DO NOt ExcEED tHE rEcOMMENDED BUlB wattaGE.

FlAme eFFeCT

The fire effect is created with the use of a 40 watt B-10 candelabra light bulb with

an e-12 (small) socket base. The light bulb will have to be replaced from time to

time when they burn out.

during normal operation, the stove heater will always give you simulated flame

function. If the intensity of flame suddenly increases, it means that the light bulb is

going to burn out.

Replace the light bulb immediately, according to the instruction. do not operate the

stove heater when the light bulb burns out or without the light bulb.

CHANGING THe lIGHT BUlB

STeP 1: open the door of unit with the handle.

STeP 2: loosen the 2 screws at the front of the log set inside the stove. Carefully

lift the logset up far enough to access the light bulbs. You will find 1 x 40 W

Type B-10 candelabra light bulb with e-12 socket base at the bottom.

STeP 3: Replace the burned out light bulb using a new 40 watt Type B-10 candelabra

light bulb.

STeP 4: Reinstall the logset.

STeP 5: Plug in the unit.

CleANING

To clean unit, first turn off the controls on the unit and unplug the unit from

power source.

To clean glass door; remove dust with clean dry cloth or to remove finger prints and

other marks clean glass with clean damp cloth. do not use abrasive cleaners

or spray liquids on the glass door surface.

metal and metal painted parts should be cleaned with a damp cloth. do not use

abrasive cleaners or spray liquids on these surfaces.

SToRAGe

When the heater is not in use, the heater should be stored in a dry location, away

from possible damage. The power cord should be stored properly to avoid contact

with hot or sharp objects.