ALIBI ALI-NS2036VR 빠른 설치 매뉴얼 - 페이지 2

{카테고리_이름} ALIBI ALI-NS2036VR에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ALIBI ALI-NS2036VR 6 페이지. 6mp vandalproof ip dome camera

페이지 인쇄

the base. An adapter plate is included. It may be needed to attach the camera to a bracket. To install

the camera:

Remove the dome cover. Use the security L-wrench provided to unscrew the three captive

screws. Lift the cover off of the mounting base assembly. A safety cable is normally attached to

the dome and the base assembly.

(Optional) Insert a microSD card into the cad slot: You can install a card with up to 128GB of

storage.

microSD card slot

RESET button*

You can install a card with up to 128GB of storage. Push the card into the slot label side up until

it clicks into place. The card should slide into the slot smoothly.

Determine the best location for mounting the camera to the mounting surface. The mounting

surface should hold at least three times the weight of the camera.

Determine the best fasteners for mounting the camera to the mounting surface. The mounting

hardware provided is adequate for many surfaces.

Using the template provided or the camera mounting base as a template, mark the locations of

the holes for the mounting screws. Also mark the location of a hole for the camera drop cables

if needed.

Drill holes into the mounting surface as needed. Also, drill a hole for the drop cable, if needed.

Route extension cables from the power source and LAN switch (or LAN with PoE) to the

mounting location.

Connect the Ethernet extension cable and power extension cable to the camera drop cables:

Connect the Ethernet extension cable to the camera network drop cable. Protect the

connection from moisture and other contamination, if necessary. A Waterproof Ethernet

Fitting is provided. Installation instructions for the fitting are included at the end of this

document.

Camera

Network drop cable

from camera

Waterproof Ethernet Fitting installed

Failure of the power or Ethernet connector due to moisture or another

contaminant is considered an installation error, which voids the warranty. If

installing this camera in a location such as an overhang, shop, garage, kitchen,

WARNING

etc. where high humidity or dust is present, seal these connections adequately.

If the camera will not use power through the 12 Vdc drop cable, ensure that the plug

provided at the end of the cable is securely in place.

If the camera is not powered using PoE (Power over Ethernet injector), connect the 12

Vdc power cable to the camera drop cable. The polarity of the drop cable connector is

shown below.

Do not apply power to the camera at this time. Before applying power to the camera, ensure



that the polarity is correct. An incorrect connection may cause a malfunction and can damage

CAUTION

the camera.

www.observint.com

10.

Step 2.

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

The Alibi Config Tool is a PC-based network utility for discovery of Alibi compatible devices. It provides

an easy way to activate devices, configure camera and recorder network configuration settings, and set

device passwords. It can be installed on a Microsoft® Windows® operating system that has direct access

to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool from

AlibiSecurity.com/Resources.

Ethernet switch or NVR

Network cable from

router or switch

NOTE

Step 3.

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

Refer to the documentation available for your NVR firmware for the procedure to activate the camera.

When an Alibi device is first installed, or reset to its factory configuration, it must be "Activated" before it

can be used. In the Alibi Configuration Tool, "Inactive" devices have a Security status of Inactive, and

an IPv4 address of 192.168.1.64. A device is "Activated" when a password is assigned to the admin

username of the device.

In the example below, an ALI-NS2036VR camera is activated and configured for its network. The procedure

is similar for all other Alibi network cameras currently available.

Route the camera drop cable through the cable channel in the base, or through the hole in the

mounting surface, and the secure the camera to the mounting surface using appropriate screws.

Mounting

surface

Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.

Install the Alibi Config Tool software

Download the Alibi Config Tool from the AlibiSecurity.com/Resources website. At the time when

this document was published, the file is named: alibi-config-tool.zip and is about 80MB.

Un-zip the file on a computer with Microsoft Windows (Windows 7 or newer) that is connected to

the LAN where your Alibi camera is connected.

Run the file contained in the zip file: Alibi Config Tool.exe. Follow the on-screen instructions to

install the file.

Open the Alibi Config Tool application. When the application opens, it automatically "discovers" and

lists all Alibi compatible devices on the LAN. See below.

In the screen above, the tool can discover devices on other sub-nets. It will also list other Alibi compatible

devices on the LAN, and devices with the address 192.168.1.64 (an inactive Alibi device).

Activate Inactive Alibi device

Peruse the list of devices the Alibi Config Tool discovered for the Inactive device you want to activate

(see below). Click on the device in the list to highlight it, and then click the select box to check it.

Mounting

screws (3)