Makita BCS550 사용 설명서 - 페이지 4
{카테고리_이름} Makita BCS550에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita BCS550 13 페이지. Cordless metal cutter 136mm (5-3/8")
Makita BCS550에 대해서도 마찬가지입니다: 부품 분석 (3 페이지), 사용 설명서 (12 페이지), 사용 설명서 (10 페이지), 기술 정보 (13 페이지)
페이지 인쇄
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use
power
tools
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal
to
another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair
person
replacement parts. This will ensure that the
safety of the power tool is maintained.
only
with
specifically
using
only
identical
29. Follow
instruction
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
CORDLESS METAL CUTTER
SAFETY WARNINGS
Cutting procedures
1.
DANGER: Keep hands away from cutting
area and the blade. Keep your second hand
on auxiliary handle, or motor housing. If both
hands are holding the tool, they cannot be cut by
blade.
2.
Do not reach underneath the workpiece. The
guard cannot protect you from the blade below
the workpiece.
3.
Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
4.
Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a
stable platform. It is important to support the
work properly to minimize body exposure, blade
binding, or loss of control.
5.
Hold
power
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
6.
When ripping, always use a rip fence or
straight edge guide. This improves the accuracy
of cut and reduces the chance of blade binding.
7.
Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the
tool will run eccentrically, causing loss of control.
8.
Never
use
washers or bolt. The blade washers and bolt
were specially designed for your tool, for optimum
performance and safety of operation.
Kickback causes and related warnings
−
Kickback is a sudden reaction to a pinched, bound
or misaligned blade, causing an uncontrolled tool to
lift up and out of the workpiece toward the operator.
−
When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator.
−
If the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the workpiece causing the
blade to climb out of the kerf and jump back
toward the operator.
4
for
lubricating
tool
by
insulated
damaged
or
incorrect
and
GEB058-3
gripping
blade