KitchenAid YKGRT607HW5 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} KitchenAid YKGRT607HW5에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid YKGRT607HW5 14 페이지. 30" freestanding and slide-in sealed burner gas range with self-cleaning thermal/convection oven

페이지 인쇄

Slide-in ranges:

countertop

preparation

30=3/8"

(77.2 cm)

opening,

width

114"

30-7/8"

(78.4 cm)

Formed or tiled

countertop

trimmed

_,_

1/4"

back at

(0.64

cm)

front corners of

countertop

opening.

The cooktop sides of the slide-in range fit over

the cutout edge of your countertop.

If you have a square finish (fiat) countertop

and the opening width is 30-3/8" (77.2 cm),

no countertop preparation is required.

Formed front-edged

countertops:

Must have

molded edge shaved fiat 1/4" (0.64 cm) from

each front corner of opening.

Tile countertops

may need trim cut back

1/4" (0.64 cm) from each front corner and/or

rounded edge flattened.

Cooktop sides of range fit over

edges of countertop

opening.

If countertop opening width is greater than

30-3/8" (77.2 cm), adjust the 1/4" (0.64 cm)

dimension.

Countertop

must be level. Place level on

countertop, first side to side; then front to back.

If countertop is not level, range will not be level.

Oven must be level for satisfactory baking

conditions.

Product dimensions

8=1/4"

(21 cm

Freestanding Range

30" (78.2 cm)

range width

36-1/8"

(91,8 cm)

cooktop

height

44-318"

(112.7 era)

-4

27-3/4"

(70,8 cm) -_

depth

with

handle

Slide-in Range

1-1/2"

(3.8 cm)

30-3/8" (77,2 cm) _4v

rear vent width

1 ,I

(2.54 cm)

spacer

27-3/4"

(70.5 cm) ._

depth

with

handle

36-1/8"

(91.8cm)

cooktop

height

30"

(76.2 cm)

width

IMPORTANT:

Rear vent must be

installed on all

slide-in models for

proper ventilation.

See Step 7, Panel D.

Panel B

Tools needed for

installation:

Phillips

screwdri_

flat-blade

screwdriver

5/16" (0,79 cm)

nut driver

ratchet wrJ

_\__pliers

_-_

measuring

tape

hammer

____

_safety

glasses

1/2" (1.3 cm)

diameter

router bit

hand or electric drill

wood floor:

1/8" (0,3 cm) drill bit

concrete/ceramic

floor:

3/16" (0.48 cm)

carbide-tipped

masonry drill bit

L,P, gas conversion

requires:

pin pick up (claw

attachment)

8/16" nut driver

Parts supplied for

installation:

(#10 x 1-1/2")

anti-tip

bracket

2 plastic

anchors

• burner grates

and caps

• vent cap

• L,P, conversion

orifice spuds kit:

2 x #64 cooktop

2 x #69 cooktop

1 x #68 broil burner

(Bracket must be securely mounted to sub-floor. Thickness

of flooring

may require longer screws to anchor the bracket

to sub-floor.)

Mobile home installation

The installation of this range must conform to the

Manufactured Home Construction and Safety

Standards, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD, Part 280); or when such

standard is not applicable, the Standard for

Manufactured Homes Installations (Manufactured

Home Sites, Communities and Setups), ANSI

A225.1/NFPA 501A*, or with local codes.

In Canada, the installation of this range must conform

with the current standards CAN/CSA-Z240 -- latest

edition**, or with local codes.

When this range is installed in a mobile home, it must

be secured to the floor during transit. Any method of

securing the range is adequate as long as it conforms

to the standards listed above.

Copies of the standards listed may be obtained from:

* National Fire Protection

Association

Batterymarch

Park

Quincy, Massachusetts

02269

** Canadian Standard

Association

178 Rexdale Boulevard

Etobicoke (Toronto), Ontario M9W 1R3

Anti-tip bracket:

The floor anti-tip bracket

MUST be installed. To install

the anti-tip bracket shipped

with the range, see Panel D

and the anti-tip bracket

template.