A&S CRAFTED PRODUCTS BAND ROOM BRUS18 조립 지침 - 페이지 2

{카테고리_이름} A&S CRAFTED PRODUCTS BAND ROOM BRUS18에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. A&S CRAFTED PRODUCTS BAND ROOM BRUS18 2 페이지. Soprano ukulele rack

페이지 인쇄

A&S CRAFTED PRODUCTS BAND ROOM BRUS18 조립 지침

3. Begin fastening one of the rails to one of the sides.

A. Holding the rail in position, remove one of the screws that you previously inserted.

Note the hole on the back side of the rail (Figure 3A).

B. Insert one of the barrel nuts into the hole on the back of the rail. The slot

should be visible and parallel with the length of the rail (Figure 3B).

C. Insert the tab portion of the rail end into the corresponding recess on the side panel

(Figure 3C-D).

D. Reinsert the screw and tighten it with a hex wrench so it is engaged in the barrel

nut (Figure 3C-D). Check to ensure that the rail tab is completely inserted into

the side panel recess.

4. Repeat steps 3A-3D for all the rails, connecting them all to the same side panel. Do not

Fig. 5

8. Attach the wheel brackets and wheels to the bottoms of the side panels.

The easiest way to do this is to rest the rack on its side (Figure 8).

A. The bracket goes on the inside of the panel, near the bottom rails. Line up the holes

in the bracket with the holes at the bottom of the side panel. The side panel should

rest on the little shelf of the bracket. The short hex screw goes into the holes from the bracket side, and

the nut goes into the holes from the outside of the panel. Use 2 hex wrenches to engage the screw in the nut. (Figure 8A)

B. Insert the stem of one of the wheels all the way into the bracket. (Figure 8B)

C. Repeat steps 8A-8B for the other 3 wheels.

9. Stand the unit upright on its wheels.

10. Install the vinyl sleeves and dowels. There are 4 colors of vinyl

sleeves that you can use for color coding, organizing, or to

provide students with choices. The vinyl sleeves cover the dowels,

and the dowels go into the holes on rails #1 and #3.

11. Remove the backing from the stickers and place them on the

outer side panels around the"sound hole" cutout (Figure 11).

A. The "sound hole" is slightly smaller than the center hole in the sticker, so

you should see a little bit of the side panel around the edges of the hole.

B. It might be helpful to fold back a portion of the backing, placing the

sticker in position, and then slowly removing the rest of the backing.

12. Insert the black ring into the "sound hole" from the same side you

applied the sticker. The ring should cover the edge of the sticker (Figure 12).

13. The long felt strips can be applied to the top surface of the #5 rails.

The felt pieces can be applied to the recessed surfaces of the #2 and #4 rails.

Enjoy your Ukulele Rack!

connect the other ends to the other side panel until all the rails

are connected at the same end to the same side panel (see step 5).

5. Stand the entire unit on end so the attached rail ends face the

floor and the unattached side panel sits on top of the rails

(Figure 5). It's a good idea to have someone help with this step.

6. At the unattached side panel (now on top), adjust the

tab ends of all the rails so they are completely inserted

into the side panel recesses.

7. Repeat steps 3A, 3B and 3D for all the rails.

ASCraftedProducts.com

Fig. 8

Fig. 8A

Fig. 11

267-626-6123

•

Back Side of Rail

Fig. 3A

Fig. 3B

Fig. 3C-D

Side

Panel

Back

Edge

Fig. 8B

Fig. 12

BRUS30/BRUS18 0517