AEG 49669GO-MN 사용자 설명서 - 페이지 25

{카테고리_이름} AEG 49669GO-MN에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AEG 49669GO-MN 38 페이지. 90cm

페이지 인쇄

solVING proBlEMs

faults

If there is a problem with the oven and / or grill, please:

• C heck the points listed below before calling for

service . It may be possible to avoid a call by fixing

the problem yourself – and so continue cooking .

NOTE: We may charge for service even in the

guarantee period if your problem is due to the causes

listed below.

problem

Oven or grill not working

Oven not heating enough

light and fans on continuously

Oven not working

Oven light not working

cooker smoking when first used

too much condensation building

up when baking

smells when first using oven

timer flashing

Burner will not light even though

the sparker is working

No spark is obtained when control

knob is activated

flames uneven or tending to lift

flames not staying on when knob

released

low heat, slow cooking

Benchtop or knobs overheating

NOTE: Only authorised personnel should carry out servicing. If the household fuse continues to blow, call the

Customer Care Centre. In the event of a power failure the gas burners may be lit with a hand held igniter and used.

Take care to avoid letting unburnt gas flow for more than 5 seconds when attempting to light the burner.

further information

when you need information, service or replacement

parts or have a warranty enquiry, please contact the

customer care centre:

• S outh Africa 0800 222 825, 7:45am – 5:00pm

please have the following information ready: Model,

Model Number & serial Number . this is shown on the

data plate which is visible when the oven door is open .

possible cause

power not turned on .

household fuse blown

controls incorrectly set

circuit breaker tripped

clock not set

foil or trays on bottom of oven

timer not in manual mode

household fuse blown

circuit breaker tripped

lamp blown or loose in socket

protective oils being removed

too much water used when cooking

protective oils being removed

power failure or interruption

knob not held down long enough in 'high'

position for flame safeguard to engage

Gas supply valve turned off

wrong knob turned off

port blockage in ignition area

Ignition spark plugs wet or dirty

Electricity supply is disconnected or

switched off

Ignition spark plugs wet or dirty

flame ports blocked or wet

Burner incorrectly fitted

knob not held down long enough in 'high'

position for flame safeguard to engage

knob not set between 'high' and 'low'

Dirt or spillage on flame safeguard sensor

Incorrect cooking pot or pan being used

pot or pan not located on burner properly

Monday to thursday, 7:45am – 4:30pm friday

what to do

switch on electricity

check fuses

reset controls

check circuit breaker

set time of day on timer

remove foil or trays

set timer to manual mode

check fuses

check circuit breaker

replace or tighten lamp

turn grill on high for 30 mins and then the

oven on 220°c for 1 hour

reduce amount of water

leave oven door open after cooking

this is normal

reset time of day

repeat lighting procedure and hold knob

down

for 5 seconds in 'high' position

turn on gas supply to appliance

Ensure the knob you are turning corresponds

to the burner you want to light

Ensure the ports in the ignition area are

clean and dry

Dry or clean ignition spark plugs

switch on electricity or check fuses

Dry or clean ignition spark plugs

clean or dry flame ports

Ensure this component is fitted correctly

repeat lighting procedure and hold knob

down for 5 seconds in 'high' position

knob Must be set between these positions

clean flameguard sensor tip

refer to cooktop section for correct

selection

refer to cooktop section for correct

selection

Ensure pot or pan is centrally located on

burner