Garmin 15L 기술 사양 - 페이지 36

{카테고리_이름} Garmin 15L에 대한 기술 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin 15L 40 페이지. Garmin gps 15l: reference guide
Garmin 15L에 대해서도 마찬가지입니다: 참조 매뉴얼 (1 페이지)

페이지 인쇄

APPENDIX E: GPS 15XH/15XL WINDOWS SERIAL MOUSE ISSUE

Problem: It is possible for Windows to incorrectly interpret the NMEA 0183 output of the GPS

15xH/15xL as the output of a Microsoft Serial BallPoint Mouse. When that happens, Windows

loads drivers for the Serial BallPoint Mouse. This causes the cursor to move erratically about the

display, clicking, right-clicking, double-clicking, and dragging and dropping displayed items as it

goes. On Windows 2000 and newer versions of Windows , you may not experience the problem if

you wait until after the computer is booted before connecting the GPS 15xH/15xL to the serial

communications port. This problem is not specific to the GPS 15xH/15xL. Any NMEA 0183 device

connected to a Windows computer's serial port is likely to cause this problem. Below are several

possible solutions to this problem.

If you wish to use a different navigation software application with your GPS 15xH/15xL, you will

need to de-select the Garmin Binary Output option that is discussed in Solution 3 below.

Solution 1: The easiest solution is to disable the Serial BallPoint mouse in the Device Manager.

This solution assumes that you do not need to use a Serial BallPoint mouse with your computer.

When erratic mouse movements occur, follow the steps below.

1. Unplug the DB9 connector.

2. Right-click the My Computer icon on your desktop, and select Properties to open Device

Manager.

3. Go to the hardware tab of the resulting pop-up window, and click on the Device Manager

button.

4. Right-click on Serial BallPoint Mouse, and choose the option to Disable (NOT uninstall) this

device.

Solution 2: Do not plug the DB9 connector into the computer until the computer is turned on and

the operating system is completely booted up and running. Every time you use the GPS

15xH/15xL, you will need to start the computer and operating system before making the

connection between the GPS 15xH/15xL and the computer. This solution usually works on

computers running Windows 2000 and newer versions of Windows.

Solution 3: Change the default output of the GPS 15xH/15xL so that it does not automatically

send NMEA 0183 data to the computer (change the default configuration to enable Garmin Binary

Output). Use the Garmin Sensor Configuration Software, named SNSRXCFG.EXE, provided on

the Web site to enable "Garmin Binary Output. To download the software, go to

https://www8.garmin.com/support/download_details.jsp?id=4053, and click Download.

NOTE: By enabling "Garmin Binary Output," the device will no longer appear as a NMEA 0183

device to your computer. As a result, mapping applications that expect to hear NMEA 0183 data

will not recognize your GPS 15xH/15xL until you re-enable the NMEA 0183 output, disabling the

Garmin Binary Output in the process.

Refer to

Appendix F: Sensor Configuration Software

the Sensor Configuration Software application.

After the Sensor Configuration Software is installed and

running on your computer, follow the steps below to

change the default data output of the GPS 15xH/15xL.

1. Select the GPS 15x/15xH/15xL from the list of

sensors, and click OK. The Sensor Configuration

Software opens with the default configuration file for

the 15xH/15xL, as shown on the next page.

2. Select Config > Switch to NMEA Mode (or press

the F10 key).

3. Select Comm > Setup to open the Comm Setup

Window.

for complete information about downloading