Garmin GPSMAP 5208 - Marine GPS Receiver 설치 지침 매뉴얼 - 페이지 2

{카테고리_이름} Garmin GPSMAP 5208 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 5208 - Marine GPS Receiver 25 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 5208 - Marine GPS Receiver에 대해서도 마찬가지입니다: 중요 안전 정보 (4 페이지), 빠른 참조 매뉴얼 (2 페이지), 소유자 매뉴얼 (2 페이지), 소유자 매뉴얼 (2 페이지), 기술 참조 (30 페이지), 설치 지침 매뉴얼 (19 페이지), 빠른 참조 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (25 페이지), 적합성 선언 (1 페이지), 인쇄 매뉴얼 (2 페이지), 보충 설명서 (24 페이지), 사용자 설명서 (6 페이지)

To install the bail-mount bracket

NotE: You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount the GPSMAP 5015/5215

chartplotter.

1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least 5 in. (12.7 cm) of clearance

behind the 4000/5000 series chartplotter for the wiring.

NotE: Mount a GPSMAP 4008/4208/5008/5208 chartplotter 31

(1 m) from a magnetic compass to avoid interference.

2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.

3. Secure the bail mount to the surface with your mounting hardware.

To install the GPSMAP 4000/5000 series chartplotter on the bail-mount bracket

1. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series chartplotter.

2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.

➊

Flush Mounting the GPSMAP 4000/5000 Series Chartplotter

The flush-mount method you will use with your chartplotter is dependent on the model. Be sure to follow the instructions for your chartplotter

model.

Flush Mounting a GPSMAP 4008/4208/4012/4212 Chartplotter or a GPSMAP 5008/5208/5012/5212

Chartplotter

Hardware (included):

• Flush-mount template

• Rubber gasket

• Four threaded 4 mm mounting studs

• Four 4-mm flat washers

• Four 4-mm lock washers

• Four 4-mm nuts

➊

in. (80 cm), and a GPSMAP 4010/4210/4012/4212/5012/5212 chartplotter 39

➋

Tools required (not included):

• Jigsaw

• Masking tape

• Scissors

• Drill

• Drill bits—

in. (10 mm) and 4 mm

•

in. (2 mm) Allen (Hex) wrench

• 4 mm socket or wrench

• Center punch and hammer

Mounting knobs ×

GPSMAP 4000/5000 Series Installation Instructions

in.