Garmin GPSMAP 5208 - Marine GPS Receiver 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} Garmin GPSMAP 5208 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 5208 - Marine GPS Receiver 25 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 5208 - Marine GPS Receiver에 대해서도 마찬가지입니다: 중요 안전 정보 (4 페이지), 빠른 참조 매뉴얼 (2 페이지), 소유자 매뉴얼 (2 페이지), 소유자 매뉴얼 (2 페이지), 기술 참조 (30 페이지), 설치 지침 매뉴얼 (19 페이지), 빠른 참조 매뉴얼 (2 페이지), 설치 지침 매뉴얼 (25 페이지), 적합성 선언 (1 페이지), 인쇄 매뉴얼 (2 페이지), 보충 설명서 (24 페이지), 사용자 설명서 (6 페이지)

페이지 인쇄
Garmin GPSMAP 5208 - Marine GPS Receiver 설치 지침 매뉴얼
Mounting a GPS 17 Antenna
You can surface mount the GPS 17 antenna or install it on a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not
included).
Surface Mounting the GPS 17 Antenna
1. Cut out the Surface Mount Drilling Template provided on page 23, and tape it on the selected mounting location.
2. Mark the center of each mounting hole with a center punch and a hammer. If you plan to run the cable through the mounting surface, mark
the center of the additional, larger hole indicated on the template.
3. Drill the mounting holes using a
a
3
/
in. (19 mm) drill bit.
4
4. If you are routing the cable through the mounting surface, feed it through the larger hole, and apply marine sealant to the outside exit area.
5. Align the GPS 17 over the mounting holes, and fasten it using M4 screws (not included). The mounting threads in the GPS 17 are 8.10 mm
deep. Use screws of a proper length for the mounting surface, which do not thread
into the GPS 17 deeper than 8 mm. Screws that thread deeper than 8 mm may
damage the case.
Mounting holes
Pole Mounting the GPS 17 Antenna
To attach the enclosed pole-mount adapter to the GPS 17:
1. Thread the cable though the pole-mount adapter.
2. Align the tab on the pole-mount adapter to the notch on the GPS 17.
3. Use the included screws to secure the pole-mount adapter to the base of the GPS 17.
Attaching the Pole-mount Adapter to the GPS 17
/
in. (4.5 mm) drill bit. If you plan to run the cable through the mounting surface, drill the larger hole using
11
64
Bottom of GPS 17 Antenna
When installing the GPS 17, you can run the power/data
When installing the GPS 17, you can run the power/data
cable through the mounting surface or outside of the unit. If
cable through the mounting surface or outside of the unit. If
the power/data cable is run through the mounting surface,
the power/data cable is run through the mounting surface,
seal the outside exit area with marine sealant.
seal the outside exit area with marine sealant.
Align Notch
GPSMAP 4000/5000 Series Installation Instructions
M4 screws
M4 screws
and washers
and washers