Garmin GHP Reactor Hydraulic 설치 지침 매뉴얼 - 페이지 13

{카테고리_이름} Garmin GHP Reactor Hydraulic에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GHP Reactor Hydraulic 15 페이지.

페이지 인쇄

High RPM Limit: Allows you to adjust the highest RPM point of

your boat. If the value does not match the value on the helm

control, you can adjust the value.

Max. Speed: Allows you to adjust the maximum speed of your

boat. If the value does not match the value on the helm

control, you can adjust the value.

Rudder Gain Settings

NOTE: If you set these values too high or too low, the autopilot

may become overactive, attempting to constantly adjust the

heading at the slightest deviation. An overactive autopilot can

cause excess wear on the pump and drain the battery at a

faster-than-normal rate.

Select Menu > Setup > Dealer Autopilot Setup > Rudder

Gains.

NOTE: These settings apply only to sailboats, displacement-hull

powerboats, and powerboats with the speed source set to None.

Gain: Allows you to adjust how tightly the rudder holds a

heading and makes turns.

Counter Gain: Allows you to adjust how tightly the rudder

corrects turn overshoot. If you set this value too low, the

autopilot can overshoot a turn when attempting to counter the

original turn.

NOTE: These settings apply only to planing-hull powerboats

with the speed source set to Tach. - NMEA 2000 or Proprietary

or GPS.

Low Speed: Allows you to set the rudder gain for low speeds.

This setting applies when the vessel operates below planing

speed.

Low Speed Counter: Allows you to set the rudder gain counter-

correction for low speeds. This setting applies when the

vessel operates below planing speed.

High Speed: Allows you to set the rudder gain for high speeds.

This setting applies when the vessel operates above planing

speed.

High Speed Counter: Allows you to set the rudder gain counter-

correction for high speeds. This setting applies when the

vessel operates above planing speed.

Steering System Settings

To open the steering system settings, select Menu > Setup >

Dealer Autopilot Setup > Steering System Setup.

Verify Steering Dir.: Allows you to set the direction the rudder

must move to turn the vessel to port and to starboard. You

can test and reverse the steering direction if necessary.

Rudder Sensor Settings

NOTE: Rudder sensor settings apply only when a rudder sensor

is connected to the autopilot system.

To open the rudder sensor settings, select Menu > Setup >

Dealer Autopilot Setup > Steering System Setup > Rudder

Sensor Setup.

Max. Port Angle: Allows you to enter the angle at which your

rudder turns furthest port.

Max. Starboard Angle: Allows you to enter the angle at which

your rudder turns furthest starboard.

Calibrate Rudder Sensor: Initiates a procedure that establishes

the maximum range of movement of the rudder and

calibrates the rudder-position sensor. If an error appears

during the calibration, the rudder-position sensor has likely

reached its limit. The sensor might not be correctly installed.

If the problem persists, you can bypass this error by moving

the rudder to the farthest position that does not report an

error.

Calibrate Rudder Center: Initiates a procedure that establishes

the center position of the rudder. You can use this calibration

if the on-screen rudder position indicator does not match the

true rudder center on your boat.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to

www.garmin.com/support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.

• In the UK, call 0808 2380000.

• In Europe, call +44 (0) 870.8501241.

and click Contact Support