Garmin GHP Reactor Hydraulic Інструкція з монтажу Посібник з монтажу - Сторінка 13
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морське обладнання Garmin GHP Reactor Hydraulic. Garmin GHP Reactor Hydraulic 15 сторінок.
Друкувати сторінку
High RPM Limit: Allows you to adjust the highest RPM point of
your boat. If the value does not match the value on the helm
control, you can adjust the value.
Max. Speed: Allows you to adjust the maximum speed of your
boat. If the value does not match the value on the helm
control, you can adjust the value.
Rudder Gain Settings
NOTE: If you set these values too high or too low, the autopilot
may become overactive, attempting to constantly adjust the
heading at the slightest deviation. An overactive autopilot can
cause excess wear on the pump and drain the battery at a
faster-than-normal rate.
Select Menu > Setup > Dealer Autopilot Setup > Rudder
Gains.
NOTE: These settings apply only to sailboats, displacement-hull
powerboats, and powerboats with the speed source set to None.
Gain: Allows you to adjust how tightly the rudder holds a
heading and makes turns.
Counter Gain: Allows you to adjust how tightly the rudder
corrects turn overshoot. If you set this value too low, the
autopilot can overshoot a turn when attempting to counter the
original turn.
NOTE: These settings apply only to planing-hull powerboats
with the speed source set to Tach. - NMEA 2000 or Proprietary
or GPS.
Low Speed: Allows you to set the rudder gain for low speeds.
This setting applies when the vessel operates below planing
speed.
Low Speed Counter: Allows you to set the rudder gain counter-
correction for low speeds. This setting applies when the
vessel operates below planing speed.
High Speed: Allows you to set the rudder gain for high speeds.
This setting applies when the vessel operates above planing
speed.
High Speed Counter: Allows you to set the rudder gain counter-
correction for high speeds. This setting applies when the
vessel operates above planing speed.
Steering System Settings
To open the steering system settings, select Menu > Setup >
Dealer Autopilot Setup > Steering System Setup.
Verify Steering Dir.: Allows you to set the direction the rudder
must move to turn the vessel to port and to starboard. You
can test and reverse the steering direction if necessary.
Rudder Sensor Settings
NOTE: Rudder sensor settings apply only when a rudder sensor
is connected to the autopilot system.
To open the rudder sensor settings, select Menu > Setup >
Dealer Autopilot Setup > Steering System Setup > Rudder
Sensor Setup.
Max. Port Angle: Allows you to enter the angle at which your
rudder turns furthest port.
Max. Starboard Angle: Allows you to enter the angle at which
your rudder turns furthest starboard.
Calibrate Rudder Sensor: Initiates a procedure that establishes
the maximum range of movement of the rudder and
calibrates the rudder-position sensor. If an error appears
during the calibration, the rudder-position sensor has likely
reached its limit. The sensor might not be correctly installed.
If the problem persists, you can bypass this error by moving
the rudder to the farthest position that does not report an
error.
Calibrate Rudder Center: Initiates a procedure that establishes
the center position of the rudder. You can use this calibration
if the on-screen rudder position indicator does not match the
true rudder center on your boat.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to
www.garmin.com/support
for in-country support information.
• In the USA, call (913) 397.8200 or (800) 800.1020.
• In the UK, call 0808 2380000.
• In Europe, call +44 (0) 870.8501241.
and click Contact Support
13