Garmin Panoptix Livescope 설치 지침 매뉴얼 - 페이지 4

{카테고리_이름} Garmin Panoptix Livescope에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Panoptix Livescope 6 페이지.

페이지 인쇄

Mounting the Sonar Module

Mounting the Panoptix LiveScope GLS 10 Device

If you are mounting the device in fiberglass, when drilling the

pilot holes, it is recommended to use a countersink bit to drill a

clearance counterbore through only the top gel-coat layer. This

will help to avoid cracking in the gel-coat layer when the screws

are tightened.

NOTE: Stainless-steel screws may bind when screwed into

fiberglass and overtightened. It is recommended to apply an

anti-seize lubricant to the screws before installing them.

NOTE: Screws are included with the device, but they may not

be suitable for the mounting surface.

Before you mount the device, you must select a mounting

location and determine what screws and other mounting

hardware are needed for the surface.

Place the device in the mounting location and mark the

location of the pilot holes.

Drill a pilot hole for one corner of the device.

Loosely fasten the device to the mounting surface with one

corner and examine the other three pilot-hole marks.

Mark new pilot-hole locations if necessary, and remove the

device from the mounting surface.

Drill the remaining pilot holes.

Secure the device to the mounting location.

Blink Codes

After the sonar module is installed, it turns on when the

chartplotter is turned on. The color status LED on the sonar

module indicates its operational status.

LED Color State

Green

Blinking

Red

Blinking

Orange

Blinking

Red/Green Blinking

Red

Two blinks

followed by a 3-

second pause

Red

Three blinks

followed by a 3-

second pause

Red

Five blinks

followed by a 3-

second pause

NOTICE

Status

The sonar module is connected to a

chartplotter and is operating properly.

You should see sonar data on the

chartplotter.

The sonar module is turned on, but is

not connected to a chartplotter, or is

waiting to connect to a chartplotter. If the

sonar module is connected to the

chartplotter and this code persists,

check the wiring connections.

A software update is in progress.

Reserved

Other sonar failure.

The transducer is not detected by the

sonar module. If this code persists,

check the wiring connections.

The sonar module input voltage exceeds

the maximum input voltage.

Installation Diagram

Compatible Garmin chartplotter

Panoptix LiveScope GLS 10 sonar module

Garmin Marine Network small connector to full-size GarminMarine

Network adapter cable

RJ-45 connector

Garmin Marine Network cable small connector

7.5 A fast-acting fuse (required, not included)

You must connect the power wire through a 7.5 A fast-acting fuse

(not included). If you omit a fuse, the device can malfunction.

Power cable

Transducer cable

Panoptix LiveScope LVS32 transducer

Power Cable Extensions

If necessary, you can extend the power cable using the

appropriate wire gauge for the length of the extension.

Item

Description

Fuse

Battery

9 ft. (2.7 m) no extension

Item Description

Splice

• 10 AWG (5.26 mm²) extension wire, up to 4.6 m (15 ft.)

• 8 AWG (8.36 mm²) extension wire, up to 7 m (23 ft.)

• 6 AWG (13.29 mm²) extension wire, up to 11 m (36 ft.)

Fuse

8 in. (20.3 cm)

Battery

8 in. (20.3 cm)

Maximum extension 36 ft. (11 m)

Calibrating the Compass

Before you can calibrate the compass, the transducer must be

installed on the shaft far enough away from the trolling motor to

avoid magnetic interference, and deployed in the water.

Calibration must be of sufficient quality to enable the internal

compass.

NOTICE