Fujitsu ABT24AG 운영 매뉴얼 - 페이지 9
{카테고리_이름} Fujitsu ABT24AG에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ABT24AG 17 페이지. Floor console/under ceiling dual type
Fujitsu ABT24AG에 대해서도 마찬가지입니다: 운영 매뉴얼 (17 페이지), 운영 매뉴얼 (17 페이지)
페이지 인쇄
TIMER OPERATION
Instructions relating to heating (*) are applicable only to "HEAT & COOL MODEL" (Reverse Cycle).
Before using the timer function, be sure that the remote control unit is set to the correct current time (See page 6).
To Use the ON timer or OFF timer
1
Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION indicator lamp (red) will light.
2
Press the TIMER button to select the OFF timer or ON
timer operation.
Each time the button is pressed the timer function changes in the follow-
ing order:
c
PROGRAM(OFF → ON, OFF ← ON)
The indoor unit's TIMER indicator lamp (green) will light.
3
Use the SET TIME buttons to adjust the desired OFF
time or ON time.
Set the time while the time display is flashing (the flashing will continue
for about five seconds).
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Use the PROGRAM timer
1
Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION indicator lamp (red) will light.
2
Set the desired times for OFF timer and ON timer.
See the section "To Use the ON timer or OFF timer" to set the desired
mode and times.
About three seconds later, the entire display will reappear.
The indoor unit's TIMER indicator lamp (green) will light.
3
Press the TIMER button to select the PROGRAM timer
operation (either OFF → ON or OFF ← ON will display).
The display will alternately show "OFF timer" and "ON timer", then change
to show the time setting for the operation to occur first.
G The PROGRAM timer will begin operation. (If the ON timer has been
selected to operate first, the unit will stop operating at this point.)
About five seconds later, the entire display will reappear.
RESET
OFF
ON
c
c
d
SLEEP
TIMER
TIMER
ON
MASTER
SET
SET
FAN
CONTROL
TEMP
.
TIME
CONTROL
To Cancel the Timer
Use the TIMER button to select "TIMER
RESET."
The air conditioner will return to normal
operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change the operating
conditions (Mode, Fan Speed, Thermostat
Setting), after making the timer setting,
wait until the entire display reappears, then
press the appropriate buttons to change to
the desired operating condition.
SLEEP
TIMER
TIMER
ON
MASTER
SET
SET
FAN
CONTROL
TEMP
.
TIME
CONTROL
To Cancel the Timer
Use the TIMER button to select "TIMER
RESET."
The air conditioner will return to normal
operation.
To Change the Timer Settings
1. Follow the instructions given in the section
"To Use the ON Timer or OFF Timer" to se-
lect the timer setting you wish to change.
2. Press the TIMER button to select either
OFF → ON or OFF ← ON.
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change the operating
conditions (Mode, Fan Speed, Thermostat
Setting), after making the timer setting,
wait until the entire display reappears, then
press the appropriate buttons to change to
the desired operating condition.
9