Brother MFC9320DW 설정 지침

{카테고리_이름} Brother MFC9320DW에 대한 설정 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother MFC9320DW 4 페이지. Wireless setup instructions for mac

페이지 인쇄

Wireless Setup Instructions for Mac

Before you begin you must know your

wireless network settings.

Write down the wireless network settings of your

access point or wireless router.

SSID (Service Set ID or Network name)

_________________________

WEP Key (if needed)

_________________________

WPA-PSK Password (if needed)

_________________________

Encryption (TKIP or AES)

_________________________

LEAP user name (if needed)

_________________________

LEAP password

_________________________

The WEP key is for 64-bit encrypted networks or

128-bit encrypted networks and can contain both

numbers and letters. If you do not know this

information you should see the documentation

provided with your access point or wireless router.

This key is a 64-bit or 128-bit value that must be

entered in an ASCII or HEXADECIMAL format.

For example:

64-bit

Uses 5 text characters.

ASCII:

e.g. "Hello" (this is case sensitive)

64-bit

Uses 10 digits of hexadecimal data.

Hexadecimal:

e.g. "71f2234aba"

128-bit

Uses 13 text characters.

ASCII:

e.g. "Wirelesscomms"

(this is case sensitive)

128-bit

Uses 26 digits of hexadecimal data.

Hexadecimal:

e.g."71f2234ab56cd709e5412aa3ba"

WPA-PSK enables a Protected Access Pre-shared

key that allows the Brother wireless machine to

associate with access points using TKIP and AES

encryption. WPA-PSK uses a Pre-Shared Key that

is 8 or more characters in length, up to a

maximum of 63 characters.

Cisco®LEAP has been developed by Cisco

Systems, Inc. which uses user ID and password

for authentication. The LEAP User ID is up to a

maximum of 63 characters in length, and the

Password is up to a maximum of 31 characters in

length.

Configure the wireless settings (typical

Wireless Setup in infrastructure mode)

(WLAN), 2 (Setup Wizard). Press 1 to choose On.

a list of SSIDs is displayed, use ▲ or ▼ to choose

your SSID, then press OK. Go to step 6.

Note:

It will take several seconds to display a list of

available SSIDs.

If your access point is set to not broadcast the

SSID you will have to manually add the SSID

name. Go to step 3.

press OK. Go to step 4.

each letter or number.

You can use ◄ and ► to move the cursor left and

right. For example, to enter the letter a, press the

2 key on the dial pad once. To enter the number

3, press the 3 key on the dial pad seven times.

The letters appear in this order: lower case, upper

case and then numbers.

Press OK when you have entered all the

characters.

press OK.

the options below: If your network is configured

for Authentication and Encryption you must match

the settings used for your network.

No Authentication or Encryption:

Choose Open System, press OK then use or to

choose None for Encryption Type? and press OK.

Then press 1 for Yes to apply your settings. Go to

step 11.

No Authentication with WEP Encryption:

Choose Open System, press OK then use or to

choose WEP for the Encryption Type? and press

OK. Go to step 7.

www.brother-usa.com

On your machine, press Menu, 7 (Network), 2

The machine will search for available SSIDs. If

Press ▲ or ▼ to choose <New SSID> and

Enter the SSID using the dial pad to choose

Press ▲ or ▼ to choose Infrastructure, then

Use the ▲ or ▼, and OK keys to choose one of