Brother MFC9320DW Installatie-instructies
Blader online of download pdf Installatie-instructies voor {categorie_naam} Brother MFC9320DW. Brother MFC9320DW 4 pagina's. Wireless setup instructions for mac
Pagina afdrukken
Wireless Setup Instructions for Mac
Before you begin you must know your
wireless network settings.
Write down the wireless network settings of your
access point or wireless router.
SSID (Service Set ID or Network name)
_________________________
WEP Key (if needed)
_________________________
WPA-PSK Password (if needed)
_________________________
Encryption (TKIP or AES)
_________________________
LEAP user name (if needed)
_________________________
LEAP password
_________________________
The WEP key is for 64-bit encrypted networks or
128-bit encrypted networks and can contain both
numbers and letters. If you do not know this
information you should see the documentation
provided with your access point or wireless router.
This key is a 64-bit or 128-bit value that must be
entered in an ASCII or HEXADECIMAL format.
For example:
64-bit
Uses 5 text characters.
ASCII:
e.g. "Hello" (this is case sensitive)
64-bit
Uses 10 digits of hexadecimal data.
Hexadecimal:
e.g. "71f2234aba"
128-bit
Uses 13 text characters.
ASCII:
e.g. "Wirelesscomms"
(this is case sensitive)
128-bit
Uses 26 digits of hexadecimal data.
Hexadecimal:
e.g."71f2234ab56cd709e5412aa3ba"
WPA-PSK enables a Protected Access Pre-shared
key that allows the Brother wireless machine to
associate with access points using TKIP and AES
encryption. WPA-PSK uses a Pre-Shared Key that
is 8 or more characters in length, up to a
maximum of 63 characters.
Cisco®LEAP has been developed by Cisco
Systems, Inc. which uses user ID and password
for authentication. The LEAP User ID is up to a
maximum of 63 characters in length, and the
Password is up to a maximum of 31 characters in
length.
Configure the wireless settings (typical
Wireless Setup in infrastructure mode)
1
(WLAN), 2 (Setup Wizard). Press 1 to choose On.
2
a list of SSIDs is displayed, use ▲ or ▼ to choose
your SSID, then press OK. Go to step 6.
Note:
It will take several seconds to display a list of
available SSIDs.
If your access point is set to not broadcast the
SSID you will have to manually add the SSID
name. Go to step 3.
3
press OK. Go to step 4.
4
each letter or number.
You can use ◄ and ► to move the cursor left and
right. For example, to enter the letter a, press the
2 key on the dial pad once. To enter the number
3, press the 3 key on the dial pad seven times.
The letters appear in this order: lower case, upper
case and then numbers.
Press OK when you have entered all the
characters.
5
press OK.
6
the options below: If your network is configured
for Authentication and Encryption you must match
the settings used for your network.
No Authentication or Encryption:
Choose Open System, press OK then use or to
choose None for Encryption Type? and press OK.
Then press 1 for Yes to apply your settings. Go to
step 11.
No Authentication with WEP Encryption:
Choose Open System, press OK then use or to
choose WEP for the Encryption Type? and press
OK. Go to step 7.
1
© 1995 - 2010 Brother International Corporation
www.brother-usa.com
On your machine, press Menu, 7 (Network), 2
The machine will search for available SSIDs. If
Press ▲ or ▼ to choose <New SSID> and
Enter the SSID using the dial pad to choose
Press ▲ or ▼ to choose Infrastructure, then
Use the ▲ or ▼, and OK keys to choose one of