Fujitsu Suelo AGY40-KV 운영 매뉴얼 - 페이지 6
{카테고리_이름} Fujitsu Suelo AGY40-KV에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu Suelo AGY40-KV 13 페이지.
Fujitsu Suelo AGY40-KV에 대해서도 마찬가지입니다: 운영 매뉴얼 (13 페이지)
페이지 인쇄
3.3. Inserting batteries
Battery type: R03/LR03/AAA x 2
1
2
9
5
1
Pull the cover in the direction of the arrow and open it
until it is trapped.
2
Remove the cover.
Turn the remote controller over and push the back
side of the cover and remove the claws by curving
the cover.
Pull in the direction of the arrow while curving the
cover.
3
Put batteries as shown in the figure above.
4
Press
as shown in the figure above.
Use the tip of a ballpoint pen or other small object.
5
Press
to start setting day of the week and clock.
6
Press
(
Sunday).
Press
to continue.
7
8
Press
(
Press the buttons to change the clock by a minute.
Press and hold the buttons to change the clock by 10 minutes.
* To switch the time indicator (12-hour ⇔ 24-hour), press
.
Press
to complete the setting.
9
Be close to the indoor unit. If you press the button from a
distance, settings may not be properly sent.
10
Install and close the cover.
NOTES:
• Use specifi ed type of batteries only.
• Do not mix diff erent types or new and used batteries together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably shortens, replace the
batteries, and press
En-5
3
7
6
RESET
8
4
to set day of the week (Monday to
)
to set the clock.
)
as shown in the fi gure above.
4. BASIC OPERATIONS
3 steps to start operation
1. Press
to start or stop the operation.
2. Press
to select the operation mode.
The operation mode changes as follows.
AUTO
COOL
3. Press
to set the desired temperature.
The temperature changes by 0.5 °C increments.
Temperature setting range
Auto/Cooling/Dry
Heating
NOTES:
• In the Cooling or Dry mode, set the temperature lower than the
current room temperature.
• In the Cooling mode, the indoor unit fan may stop from time to time
to perform Fan control for energy saving that enables power-saving
operation by stopping the rotation of the indoor unit fan when the
outdoor unit is stopped.
In initial setting, this function is activated.
To deactivate the function, consult the installer or authorized service
personnel.
• In the Heating mode,
- set the temperature higher than the current room temperature.
- at the beginning of the operation, the indoor unit fan rotates at very
low speed for 3-5 minutes.
- the Automatic defrosting operation overrides the Heating operation
when necessary.
• In the Fan mode, temperature control is not available.
Temperature unit switching
1. Press
until only the clock is displayed.
2. Press down
for more than 5 seconds.
The current temperature unit will be displayed. (Factory setting: °C)
3. Press
to switch the temperature unit. (°C ⇔ °F)
4. Press
to fi nish the setting.
If you do not press the button for 30 seconds, the displayed
temperature unit will be set.
5. AIRFLOW SETTINGS
5.1. Fan speed setting
Press
to control the fan speed.
The fan speed changes as follows.
(Auto)
(High)
When
is selected, the fan speed depends on the operating
condition.
To increase the air cleaning eff ect, set the fan speed to High.
DRY
FAN
HEAT
18.0 to 30.0 °C
16.0 to 30.0 °C
(Med)
(Low)
(Quiet)