Fujitsu Primergy BX620 S3 시스템 구성 및 주문 정보 매뉴얼 - 페이지 5

{카테고리_이름} Fujitsu Primergy BX620 S3에 대한 시스템 구성 및 주문 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu Primergy BX620 S3 18 페이지.

페이지 인쇄

PRIMERGY BX620 S2 / BX620 S3

PRIMERGY BX620 S2

Configuration Diagram

Memory

CPU

DIMM Slot 1

Xeon®

DIMM Slot 2

3.80/3.40E/

DIMM Slot 3

3.20E/3EGHz

DIMM Slot 4

(2MB)

DIMM Slot 5

DIMM Slot 6

Xeon®

3.80/3.40E/

3.20E/3EGHz

Expansion Board Slot *1,*2

(2MB)

*1. When 2Gbit/s FC I/O Module (PG-FCD102) is mounted on Expansion Board Slot of BX620 S2, FC Switch Blade (PG-FCS102) or FC Pass-Thru Blade (PG-FCB101)

is required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC1).

BX620 S2 / BX620 S3 with 1Gbit/s Ethernet I/O Module (PG-LND101) and BX620 S2 / BX620 S3 with 2Gbit/s FC I/O Module (PG-FCD102)

are not allowed to be mounted together on same BX600 S2 Blade Server System Unit (PGUR3SC1).

*2. When 1Gbit/s Ethernet I/O Module (PG-LND101) is mounted on Expansion Board Slot of BX620 S2, Switch Blade (PG-SW104/PG-SW105) or GbE Pass-Thru Blade (PG-LNB101)

is required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC1).

BX620 S2 / BX620 S3 with 1Gbit/s Ethernet I/O Module (PG-LND101) and BX620 S2 / BX620 S3 with 2Gbit/s FC I/O Module (PG-FCD102)

are not allowed to be mounted together on same BX600 S2 Blade Server System Unit (PGUR3SC1).

*3. When Expansion Card Slot Module (PG-CS102) is mounted, HDD can not be mouted on 3.5 inch HDD Bay 2.

*Components installed as standard configuration marked in grey.

Mountable I/O Options

BX620 S2 ( In case that Expansion Card Slot Module (PG-CS102) is applied. )

Mountable Cards

Eth. Ctrl 2x1000-BASE-T Cu

PG-1862

SCSI Ctrl U160

PG-128

*. PCI card (Eth. Ctrl 2x1000-BASE-T Cu(PG-1862),SCSI Ctrl U160(PG-128)) should be mounted on Expansion Card Slot Module(PG-CS102).

The slot of mounted PCI card is at front side of BX600 S2 Blade Server System Unit (PGUR3SC1).

The cable connected to PCI card can be gone from front side to back side of BX600 S2 Blade Server System Unit (PGUR3SC1)

by using Front-Rear Cable-Thru kit (PG-R1CM1).

Front-Rear Cable-Thru kit (PG-R1CM1) is mounted just under BX620 S2 and occupies 1U.

Connection Table

CPU

Max: 2 CPU

CPU Slot

Standard: 1 CPU

*CPU Conversion Kit (available only for a Configure to Order (CTO) option; no separate shipment is possible)

Type

Product ID

CPU Conversion Kit:

Xeon (3.0GHz/2MB)

PGBFU36D

-> Xeon(3.8GHz/2MB)

(for CTO)

CPU Conversion Kit:

Xeon (3.0GHz/2MB)

PGBFU36C

-> Xeon(3.4GHz/2MB)

(for CTO)

CPU Conversion Kit:

Xeon (3.0GHz/2MB)

PGBFU263

-> Xeon(3.2GHz/2MB)

(for CTO)

3.5 inch HDD Bay 1

(hot plug)

3.5 inch HDD Bay 2

(hot plug) *3

Max No.

Bus

of Mount

PCI-X/64bit

PCI/64bit

For PRIMERGY SX10

64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.80GHz

Convert the CPU installed as standard in the base unit to the other.

(Note: This option can be ordered only as coupled with the base unit.

A separate shipment is not possible.)

64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.40EGHz

Convert the CPU installed as standard in the base unit to the other.

(Note: This option can be ordered only as coupled with the base unit.

A separate shipment is not possible.)

64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.20EGHz

Convert the CPU installed as standard in the base unit to the other.

(Note: This option can be ordered only as coupled with the base unit.

A separate shipment is not possible.)

Hard Disk 3.5inch Bay (hot plug)

Standard Drive Cage (HDD x 1ch)

Bay 1

Bay 2

SCSI

Remarks

Processor Xeon 3.8GHz/2MB

PG-FG36D

PGBFG36D (for CTO)

*. This option is available when CPU Conversion Kit:

Xeon(3.0GHz/2MB) -> Xeon(3.8GHz/2MB) (PGBFU36D) is applied.

Processor Xeon 3.4GHz/2MB

PG-FG36C

PGBFG36C (for CTO)

*. This option is available when CPU Conversion Kit:

Xeon(3.0GHz/2MB) -> Xeon(3.4GHz/2MB) (PGBFU36C) is applied.

Processor Xeon 3.2GHz/2MB

PG-FG263

PGBFG263 (for CTO)

*. This option is available when CPU Conversion Kit:

Xeon(3.0GHz/2MB) -> Xeon(3.2GHz/2MB) (PGBFU263) is applied.

Processor Xeon 3.0GHz/2MB

PG-FG262

PGBFG262 (for CTO)

*. This option is available when the processor of the base unit

is Processor Xeon 3.0GHz/2MB.