Fujitsu Primergy BX620 S3 Podręcznik konfiguracji systemu i informacji o zamówieniach - Strona 5

Przeglądaj online lub pobierz pdf Podręcznik konfiguracji systemu i informacji o zamówieniach dla Serwer Fujitsu Primergy BX620 S3. Fujitsu Primergy BX620 S3 18 stron.

Drukuj stronę
PRIMERGY BX620 S2 / BX620 S3
PRIMERGY BX620 S2

Configuration Diagram

Memory
CPU
DIMM Slot 1
Xeon®
DIMM Slot 2
3.80/3.40E/
DIMM Slot 3
3.20E/3EGHz
DIMM Slot 4
(2MB)
DIMM Slot 5
DIMM Slot 6
Xeon®
3.80/3.40E/
3.20E/3EGHz
Expansion Board Slot *1,*2
(2MB)
*1. When 2Gbit/s FC I/O Module (PG-FCD102) is mounted on Expansion Board Slot of BX620 S2, FC Switch Blade (PG-FCS102) or FC Pass-Thru Blade (PG-FCB101)
is required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC1).
BX620 S2 / BX620 S3 with 1Gbit/s Ethernet I/O Module (PG-LND101) and BX620 S2 / BX620 S3 with 2Gbit/s FC I/O Module (PG-FCD102)
are not allowed to be mounted together on same BX600 S2 Blade Server System Unit (PGUR3SC1).
*2. When 1Gbit/s Ethernet I/O Module (PG-LND101) is mounted on Expansion Board Slot of BX620 S2, Switch Blade (PG-SW104/PG-SW105) or GbE Pass-Thru Blade (PG-LNB101)
is required to be mounted on Network Blade Slot 3,4 of BX600 S2 Blade Server System Unit (PGUR3SC1).
BX620 S2 / BX620 S3 with 1Gbit/s Ethernet I/O Module (PG-LND101) and BX620 S2 / BX620 S3 with 2Gbit/s FC I/O Module (PG-FCD102)
are not allowed to be mounted together on same BX600 S2 Blade Server System Unit (PGUR3SC1).
*3. When Expansion Card Slot Module (PG-CS102) is mounted, HDD can not be mouted on 3.5 inch HDD Bay 2.
*Components installed as standard configuration marked in grey.
Mountable I/O Options
BX620 S2 ( In case that Expansion Card Slot Module (PG-CS102) is applied. )
Mountable Cards
Eth. Ctrl 2x1000-BASE-T Cu
PG-1862
SCSI Ctrl U160
PG-128
*. PCI card (Eth. Ctrl 2x1000-BASE-T Cu(PG-1862),SCSI Ctrl U160(PG-128)) should be mounted on Expansion Card Slot Module(PG-CS102).
The slot of mounted PCI card is at front side of BX600 S2 Blade Server System Unit (PGUR3SC1).
The cable connected to PCI card can be gone from front side to back side of BX600 S2 Blade Server System Unit (PGUR3SC1)
by using Front-Rear Cable-Thru kit (PG-R1CM1).
Front-Rear Cable-Thru kit (PG-R1CM1) is mounted just under BX620 S2 and occupies 1U.

Connection Table

CPU
Max: 2 CPU
CPU Slot
Standard: 1 CPU
*CPU Conversion Kit (available only for a Configure to Order (CTO) option; no separate shipment is possible)
Type
Product ID
CPU Conversion Kit:
Xeon (3.0GHz/2MB)
PGBFU36D
-> Xeon(3.8GHz/2MB)
(for CTO)
CPU Conversion Kit:
Xeon (3.0GHz/2MB)
PGBFU36C
-> Xeon(3.4GHz/2MB)
(for CTO)
CPU Conversion Kit:
Xeon (3.0GHz/2MB)
PGBFU263
-> Xeon(3.2GHz/2MB)
(for CTO)
3.5 inch HDD Bay 1
(hot plug)
3.5 inch HDD Bay 2
(hot plug) *3
Max No.
Bus
of Mount
1
PCI-X/64bit
1
1
PCI/64bit
For PRIMERGY SX10
64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.80GHz
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
A separate shipment is not possible.)
64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.40EGHz
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
A separate shipment is not possible.)
64-bit Intel® Xeon® 3EGHz -> 64-bit Intel® Xeon® 3.20EGHz
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
A separate shipment is not possible.)
Hard Disk 3.5inch Bay (hot plug)
Standard Drive Cage (HDD x 1ch)
Bay 1
Bay 2
SCSI
SCSI
Remarks
Processor Xeon 3.8GHz/2MB
PG-FG36D
PGBFG36D (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon(3.0GHz/2MB) -> Xeon(3.8GHz/2MB) (PGBFU36D) is applied.
Processor Xeon 3.4GHz/2MB
PG-FG36C
PGBFG36C (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon(3.0GHz/2MB) -> Xeon(3.4GHz/2MB) (PGBFU36C) is applied.
Processor Xeon 3.2GHz/2MB
PG-FG263
PGBFG263 (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon(3.0GHz/2MB) -> Xeon(3.2GHz/2MB) (PGBFU263) is applied.
Processor Xeon 3.0GHz/2MB
PG-FG262
PGBFG262 (for CTO)
*. This option is available when the processor of the base unit
is Processor Xeon 3.0GHz/2MB.