Fujitsu ETERNUS DX Disk 구성 매뉴얼 - 페이지 14

{카테고리_이름} Fujitsu ETERNUS DX Disk에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ETERNUS DX Disk 21 페이지. Server connection, fcoe for linux driver settings for converged network adapter cards
Fujitsu ETERNUS DX Disk에 대해서도 마찬가지입니다: 사용자 설명서 (35 페이지), 사용자 설명서 (42 페이지), 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (44 페이지), 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (29 페이지), 구성 매뉴얼 (25 페이지), 구성 매뉴얼 (32 페이지), 구성 매뉴얼 (35 페이지), 구성 매뉴얼 (31 페이지), 구성 매뉴얼 (43 페이지), 구성 매뉴얼 (24 페이지)

페이지 인쇄
Fujitsu ETERNUS DX Disk 구성 매뉴얼
Chapter 2
Setup Procedure for QLogic Converged Network Adapter Cards
2.2
Setting Up the Converged Network Adapter Cards
7
Perform the BIOS settings for the Converged Network Adapter card.
Check the parameter values in the [Adapter Settings] window against those in the following table. For
details on how to set the values, refer to the BIOS Readme file and Converged Network Adapter card
user's guide.
Parameter
BIOS Address
BIOS Revision (*1)
Adapter Mac Address
Interrupt Level
Adapter Port Name
Host Adapter BIOS
Frame Size
Loop Reset Delay
Spinup Delay
Fibre Channel Tape Support
*1: The BIOS version of the Converged Network Adapter card is displayed. Check that the BIOS version
is the same as shown in "Server Support Matrix".
8
Return to the [Configuration Settings] menu by pressing the [Esc] key.
9
Select [Advanced Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.
Check the parameter values in the [Advanced Adapter Settings] window against those in the following
table.
Parameter
Execution Throttle
LUNs per Target
Enable Target Reset
Login Retry Count
Port Down Retry Count
Link Down Timeout
Operation Mode
Interrupt Delay Timer
Enable Interrupt
EV Controller Order
LR Enable
Primary FCF VLAN ID
*1: Recommended value = 1024 ¸ (number of FCoE ports that are connected to a single CA port) ¸
number of LUNs
(Round the result down)
•
Use the value of "8" if the actual result is lower. Use the maximum value if the actual result ex-
ceeds the maximum value of the OS or the driver.
Setting value
Fixed for each card
Disabled
2048
5
Disabled
Disabled
Setting value
Arbitrary (*1)
(Up to 1024 for each FCoE port of the
ETERNUS DX)
128
Yes
8
30
30
0
0
NO
Disabled
Disabled
Disabled
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (FCoE) for Linux
Copyright 2018 FUJITSU LIMITED
14
Remarks
Settings cannot be changed.
If the current parameter values are dif-
ferent, change them to the indicated
values.
Remarks
If the current parameter values are dif-
ferent, change them to the indicated
values.
P3AM-6402-11ENZ0