Fujitsu ETERNUS DX Disk 구성 매뉴얼 - 페이지 16

{카테고리_이름} Fujitsu ETERNUS DX Disk에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fujitsu ETERNUS DX Disk 21 페이지. Server connection, fcoe for linux driver settings for converged network adapter cards
Fujitsu ETERNUS DX Disk에 대해서도 마찬가지입니다: 사용자 설명서 (35 페이지), 사용자 설명서 (42 페이지), 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (44 페이지), 구성 매뉴얼 (28 페이지), 구성 매뉴얼 (29 페이지), 구성 매뉴얼 (25 페이지), 구성 매뉴얼 (32 페이지), 구성 매뉴얼 (35 페이지), 구성 매뉴얼 (31 페이지), 구성 매뉴얼 (43 페이지), 구성 매뉴얼 (24 페이지)

페이지 인쇄
Fujitsu ETERNUS DX Disk 구성 매뉴얼
Chapter 2
Setup Procedure for QLogic Converged Network Adapter Cards
2.4

Setting Up the Driver Parameters

2.4
Setting Up the Driver Parameters
Use an editor such as "vi" to add the setting values to the configuration file.
Note that the setting values and details vary depending on the OS vender, version, whether the ETERNUS
Multipath Driver is used, and the storage system that is used.
●
When the ETERNUS Multipath Driver is not used
Configuration file
•
OS
Red Hat Enterprise Linux 7
Red Hat Enterprise Linux 6
Red Hat Enterprise Linux 5
SUSE Linux Enterprise Server 12
SUSE Linux Enterprise Server 11
SUSE Linux Enterprise Server 10
If the same driver parameter is already set in the configuration file, only the value for the parameter
must be changed.
Setting details
•
In the following tables, "N" indicates the value of the driver parameter setting.
OS
Red Hat Enterprise Linux 7
Red Hat Enterprise Linux 6
Red Hat Enterprise Linux 5
SUSE Linux Enterprise Server 12
SUSE Linux Enterprise Server 11
SUSE Linux Enterprise Server 10
"scsi_hostadapterX" indicates that a digit starting from 2 is added after the "scsi_hostadapter" string
when SCSI devices or SCSI-RAID devices are installed in the system.
Driver parameter settings
•
Driver parameter
ql2xfailover=
ql2xmaxqdepth=
ql2xtgtemul=
Configuration file
Any file (.conf) in /etc/modprobe.d/
Any file (.conf) in /etc/modprobe.d/
/etc/modprobe.conf
Any file (.conf) in /etc/modprobe.d/
/etc/modprobe.conf.local
/etc/modprobe.conf.local
Setting details
options qla2xxx ql2xmaxqdepth=N
options qla2xxx ql2xmaxqdepth=N
alias scsi_hostadapterX qla2xxx
options qla2xxx ql2xfailover=0 ql2xmaxqdepth=N ql2xtgtemul=0
options qla2xxx ql2xmaxqdepth=N
options qla2xxx ql2xmaxqdepth=N
options qla2xxx ql2xfailover=0 ql2xmaxqdepth=N ql2xtgtemul=0
Setting value
0
Arbitrary (*1)
(Up to 1024 for each FCoE port of the ETERNUS DX)
0
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (FCoE) for Linux
Copyright 2018 FUJITSU LIMITED
16
P3AM-6402-11ENZ0