Indesit IDCE 845 A 사용 설명서 - 페이지 14

{카테고리_이름} Indesit IDCE 845 A에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit IDCE 845 A 20 페이지. Indesit clothes dryer user manual
Indesit IDCE 845 A에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 사용 설명서 (20 페이지)

페이지 인쇄

Care and maintenance

Disconnecting the power supply

Disconnect the dryer when not in use or during cleaning

and maintenance operations.

Cleaning the filter after each cycle

The filter is a fundamental component of the dryer: its function

is to collect lint and fluff that form during drying.

Clean the filter once drying is completed, by rinsing it under run-

ning water or cleaning it with a vacuum cleaner. Should the filter

become clogged, the flow of air inside the dryer will be seriously

hampered: drying times becomes longer and more energy is

consumed. Moreover, the dryer may become damaged.

The filter is located in front of the dryer seal (see Picture).

Removing the filter:

Checking the drum after each cycle

Rotate the drum manually to remove smaller items (handker-

chiefs) that could have been left inside the dryer.

Cleaning the drum

Avoid using abrasives, steel wool or stainless steel cleaning

agents to clean the drum. A coloured film may appear on the

stainless steel drum surface: it may be caused by a combina-

tion of water and/or cleaning agents such as wash-softeners.

This coloured film does not affect the dryer's performance.

Emptying the water container after

each cycle

Remove the water container and empty it into a sink or other

suitable drain outlet, then replace it correctly.

Always check the water container and empty it before star-

ting a new drying cycle.

1. Pull the filter's plastic han-

dle upwards (see Picture).

2. Clean the fluff off the filter

and replace it correctly. En-

sure that the filter is pushed

fully home.

Do not use the dryer unless

the filter has been replaced in

its holder.

Water container

Heat pump

filter unit

Catches

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove Heat pump filter

unit and clean any build up of fluff from the surface of the

filter by rinsing it under running water or with your vacuum

cleaner.

We however recommend that you clean this filter after

every drying cycle to optimize the dryers performance.

To remove Heat pump filter unit:

1. Unplug the dryer and open the door.

2. Remove the filter unit by rotating the 4 clips to the vertical

position then pulling the filter unit towards you.

3. Separate the two parts of the filter

unit and clean the surface of the filter.

! Warning: The front of the heat

pump is made from thin metal

plates.

Take care that you do not damage

these or cut yourself when cleaning,

removing or replacing the filter unit.

4. If there is any build up of fluff on

the plates Carefully clean this off with a damp cloth,sponge

or vacuum cleaner. Never use your Fingers.

5. Assemble the two parts of the filter clean the surface of

the seals and replace with the 4 clips into the horizontal

position, sure that the catches have been secured.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be clea-

ned with a damp cloth.

• Clean the front air intake grille regularly (every 6 months)

with a vacuum cleaner to remove any lint, fluff or dust

deposits. Furthermore, remove any lint deposits from the

front part of the condenser and from the filter area, using a

vacuum cleaner every so often.

Do not use solvents or abrasives.

Have the dryer checked regularly by authorised technical

personnel in order to ensure that the electrical and mechani-

cal parts work safely (see Assistance).

Filter

Air intake

Condenser cover

Handle