Indesit IDCE 845 A Інструкція з експлуатації - Сторінка 14
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Сушарка Indesit IDCE 845 A. Indesit IDCE 845 A 20 сторінок. Indesit clothes dryer user manual
Також для Indesit IDCE 845 A: Інструкція з експлуатації (20 сторінок), Інструкція з експлуатації (20 сторінок)
Друкувати сторінку
Care and maintenance
Disconnecting the power supply
EN
!
Disconnect the dryer when not in use or during cleaning
and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the dryer: its function
is to collect lint and fluff that form during drying.
Clean the filter once drying is completed, by rinsing it under run-
ning water or cleaning it with a vacuum cleaner. Should the filter
become clogged, the flow of air inside the dryer will be seriously
hampered: drying times becomes longer and more energy is
consumed. Moreover, the dryer may become damaged.
The filter is located in front of the dryer seal (see Picture).
Removing the filter:
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handker-
chiefs) that could have been left inside the dryer.
Cleaning the drum
!
Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a combina-
tion of water and/or cleaning agents such as wash-softeners.
This coloured film does not affect the dryer's performance.
Emptying the water container after
each cycle
Remove the water container and empty it into a sink or other
suitable drain outlet, then replace it correctly.
Always check the water container and empty it before star-
ting a new drying cycle.
14
1. Pull the filter's plastic han-
dle upwards (see Picture).
2. Clean the fluff off the filter
and replace it correctly. En-
sure that the filter is pushed
fully home.
!
Do not use the dryer unless
the filter has been replaced in
its holder.
Water container
Heat pump
filter unit
Catches
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove Heat pump filter
unit and clean any build up of fluff from the surface of the
filter by rinsing it under running water or with your vacuum
cleaner.
We however recommend that you clean this filter after
every drying cycle to optimize the dryers performance.
To remove Heat pump filter unit:
1. Unplug the dryer and open the door.
2. Remove the filter unit by rotating the 4 clips to the vertical
position then pulling the filter unit towards you.
3. Separate the two parts of the filter
unit and clean the surface of the filter.
! Warning: The front of the heat
pump is made from thin metal
plates.
Take care that you do not damage
these or cut yourself when cleaning,
removing or replacing the filter unit.
4. If there is any build up of fluff on
the plates Carefully clean this off with a damp cloth,sponge
or vacuum cleaner. Never use your Fingers.
5. Assemble the two parts of the filter clean the surface of
the seals and replace with the 4 clips into the horizontal
position, sure that the catches have been secured.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be clea-
ned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
!
Do not use solvents or abrasives.
!
Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
Filter
Air intake
Condenser cover
Handle