Aqua Quip JET-VAC 설치 설명서 및 사용 설명서 - 페이지 2

{카테고리_이름} Aqua Quip JET-VAC에 대한 설치 설명서 및 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aqua Quip JET-VAC 12 페이지. Automatic pool cleaner
Aqua Quip JET-VAC에 대해서도 마찬가지입니다: 설치 설명서 및 사용 설명서 (12 페이지)

페이지 인쇄

CONGRATULATIONS on purchasing Jet-Vac, the finest pool cleaner available today.

Jet-Vac has a patented, built-in backup system that will move the unit out of corners and

away from other obstacles that tend to trap other pool cleaners. The unit moves forward

for approximately three minutes, then backs up and turns for approximately 45 seconds,

all the while vacuuming and sweeping your pool in a random pattern. It is designed with

fewer moving parts to give you years of dependable, economical service.

Jet-Vac is proudly made in Australia, built from the best materials obtainable using state-

of-the-art machinery and is backed by a one year limited warranty that guards against

defects in parts and workmanship.

Important Information for Installer

Like any other mechanical device, the Jet-Vac

should be routinely maintained. Jet-Vac travels over

1,000 kilometres (620 miles) per year, underwater.

Therefore, we recommend that you have your

Jet-Vac checked periodically by your local pool

professional.

Not only does Jet-Vac pick up leaves, debris, sand

and silt, it also spreads your chlorine all over the pool

and ensures sparkling clean water all the time. There

are a few hints, which will help you prolong the life of

your Jet-Vac and reduce operating costs at the

same time.

• Jet-Vac is not designed to clean up after new pool

construction. Large amounts of pebbles, grit and

sand can damage the wheel bearings. Please

manually vacuum the pool thoroughly before

installing the Jet-Vac.

• If your new Jet-Vac tends to fly around the pool,

remove the Jet-Vac and lay the feed hoses and

sweep hose out in the sun for 1-2 days. This will

remove the hoses "memory" of being coiled up.

• Jet-Vac is a very efficient pool cleaner and normally

only requires 2-3 hours of use per day. The Jet-

Vac booster pump can only run while the pool

pump is operating. To achieve this, we strongly

recommend that a separate time clock is installed.

For Australian customers we recommend the

Aqua-Quip Flow Control Pro Series Timer. This will

minimize the risk of your Jet-Vac pump running

dry and will significantly reduce ongoing repair

costs. The Flow Control Pro Series Timer is simple

to install and is available from your local pool

professional.

• The inner surface of a concrete pool can be

abrasive and the Jet-Vac will have certain

components wearing down over time. The wheels

have special wear indicator grooves molded in

so that you can easily tell when they need to be

replaced.

J E T - V A C

JET-VAC

and Jet-Vac Owner

A U T O M A T I C

P O O L

C L E A N E R

AUTOMATIC

POOL CLEANER

• Empty the leaf bag regularly. Failure to do this

results in twigs ripping the bag or the bag dragging

along the surface of the pool, resulting in premature

failure.

• When removing Jet-Vac from the pool for an

extended time, always lay the hose straight. Do

not store the Jet-Vac hose coiled up. Never store

Jet-Vac exposed to direct sunlight.

• If the Jet-Vac starts to move more slowly than

normal, check the filter screen inside the white

wall fitting. To clean the filter screen: Push in and

turn the bayonet style wall fitting anti-clockwise to

release it from the wall adaptor. Remove mesh filter

screen for cleaning. O-ring on wall fitting should

be lubricated regularly to enable easy removal.

Clean this filter screen regularly to ensure efficient

operation at all times.

• Before backwashing the filter, turn the Jet-Vac

pump off. Disconnect bayonet wall fitting from

wall adaptor. Backwash the filter according to

manufacturer's instructions. After backwashing is

complete, turn on pool pump to run on filter cycle

and then switch Jet-Vac pump on for 10 seconds.

This will dislodge any debris caught in the Jet-Vac

supply line. The Jet-Vac pump will run noisy whilst

running without the wall fitting attached for this

short period of time. Turn off the Jet-Vac pump and

pool pump, reconnect Jet-Vac bayonet wall fitting

onto wall adaptor. Place Jet-Vac cleaner into pool.

• After turning on the pool pump and Jet-Vac pump

you may find air accumulating in the leaf bag. If so,

release it by gently touching the top of the leaf bag

with a telepole or similar device. Air will be released

through the mesh air-release material at the top of

the leaf bag.

• Never operate your Jet-Vac without a booster

pump. Your existing filter system cannot generate

adequate pressure.

• Always remove Jet-Vac and hoses when adding

chemicals. Run filter to mix chemicals in water for

at least 30 minutes before reinstalling Jet-Vac and

hoses in water.

–

I N S T A L L A T I O N

O P E R A T I N G

I N S T R U C T I O N S