Avue G40 사용자 설명서 - 페이지 7

{카테고리_이름} Avue G40에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Avue G40 14 페이지. Middle speed dome camera series

페이지 인쇄

5.OPERATING THE SPEED DOME

Initial Screen

After powering up, the camera will enter into

FIRMWARE

V1.03

the self-test mode and display the status

Protocol: PELCO

screen (see picture left). It contains

Dome Address: 001

information about the model and current

Comm 9600,N,8,1

settings.

- "

FIRMWARE

": Model number

- V1.03: Current firmware version

- Protocol: Control protocol which currently used

- Dome address: Address ID of speed dome. Please refer to the section "Protocol

setup " for details

- Comm 9600,N,8,1: Current setting of the serial communication interface

9600: Baud rate. Please refer to section "Baud-Rate setup" for details

N, 8, 1: No parity bit, 8 bit length, 1 stop bit. This setting cannot be changed

The intial screen will remain on until any user action is taken. If the power-up action is

set, the initial info wil vanish immediately.

Operation Screen

The operation screen can display additional

information.

Temperature: Current temperature inside the speed

dome( °C)

Cam title:

User definable camera title

Zone:

Current zone name

Pan deg.:

Pan angle, 0-359°

Tilt deg.:

Tilt angle, 0-90°

Zoom Factor: Zoom factor

Display of the information can be activated or

deactivated through the OSD menu.Pplease refer to

the system setting for detais.

PTZ operation

For the surveillance operation, the dome can be controlled from a keyboard device,

Multiplexer or DVR through RS485 interface. Make sure that the cable is connected

and the settings (baud rate, Address ID and protocol) of both, keyboard and the dome,

are correctly configurated. For further details on operating the PTZ, please refer to the

user's manual of the keyboard.

Some products may not be available in your country, please contact our distributor for more details

Temperature

CAM TITLE

32.0

ZONE-1

285 78

18X

Zoom factor

Tilt degree

Pan degree

Zone description

6.OSD

OSD Menu

The dome camera are equipped with the new OSD Menu function. All operational functions

and camera related settings can be controlled here. In order to use the OSD function, a

telemetric controller device, such as keyboard, DVR or other devices with similiar functions,

is required. Please make sure that the device used is properly physically connected to the

dome and all connection parameters are set.

How to start the OSD Menu

To start the OSD Menu, you need to press the following sequence on the keyboard:

call

With

keyboard

Shot

With keyboard

(

3-Axis

)

In case a DVR is used for operating the OSD, select "go to preset 95" or 2 X "go to preset 9".

Please refer to the DVR's operation manual for more details.

Note that in some situations, it is not possible to access the OSD menu:

1. The dome is running a tour

2. Performing PTZ operations

3. Dome is receiving a command other than OSD-request from the keyboard

To solve this inability stop the operation and try again.

Main menu and navigation

After entering the OSD Menu, the screen will show

menu items . Use the controller's joystick to navigate

Main Menu

the menu's main and sub items by moving in the

desired direction. The angle mark on the beginning of

SYSTEM SETTING

every item indicates the selection.

CAMERA SETTING

FUNCTION SETTING

UP, DOWN:

WINDOW BLANKING

ALARM

RIGHT:

EXIT

LEFT:

For more inforamtion, please refer to the illustration on

Symbols and indicator

Cursor.

Sub item is selected. use up or down to change value

This item has subitem(s)

Some products may not be available in your country, please contact our distributor for more details

call

2 X

Enter

2 X

Enter

Shot

- Moving between current menu items

- Changing the value in sub items

- Enter the selected menu item

- Confirm the value change and return

item selection

- Exit from sub menu