Dell EMC PowerSwitch N3048ET-ON 펌웨어 업그레이드 방법 - 페이지 11
{카테고리_이름} Dell EMC PowerSwitch N3048ET-ON에 대한 펌웨어 업그레이드 방법을 온라인으로 검색하거나 PDF를 다운로드하세요. Dell EMC PowerSwitch N3048ET-ON 21 페이지.
페이지 인쇄
Upgrade Dell EMC Networking N3000E-ON Switches
9. Power ON stack (N3000E-ON series with N3000 Series).
10. Verify the stack of N3000E-ON Series and N3000 Series switches via show switch and show version
command output like below:
Console#show switch
Management Standby
SW
Status
--- ---------- --------- ------------- ------------- ------------- -----------
1
Stack Mbr
2
Mgmt Sw
Console#show version
Machine Description............... Dell EMC Networking Switch
System Model ID................... N3048EP-ON
Machine Type...................... Dell EMC Networking N3048EP-ON
Serial Number.....................
Manufacturer...................... 0xbc00
Burned In MAC Address............. 0090.BC06.A571
System Object ID.................. 1.3.6.1.4.1.674.10895.3060
SOC Version....................... BCM56340_A0
HW Version........................ 5
CPLD Version...................... 20
Image File........................ N3000AdvLitev6.5.3.6
Software Capability............... Stack Limit = 8, VLAN Limit = 1024
unit active
---- ----------- ----------- -------------- --------------
1
6.5.3.6
2
6.5.3.6
Administrators setting up mixed stack of N3000E-ON and N3000 Stacked switches should follow the below steps
below:
1. Back up your configuration of N3000E-ON Stack and N3000 Stack Switches.
2. Upgrade using telnet or SSH require default enable authentication method or enable password in current
configuration. If not configured follow steps below to configure an enable password:
console#configure
console(config)#enable password <password>
console(config)#exit
console#copy running-config startup-config
3. Download the 6.5.3.6 firmware image (N3000AdvLitev6.5.3.6.stk) to stack of N3000E-ON switches and
stack of N3000 switches.
NOTE:
Activate the image to use as the boot (active) image after the stack
resets. Images on the N3000E-ON stack is named as active and backup.
4. Activate 6.5.3.6 (Advanced-Lite) firmware on stack of N3000E-ON switches and stack of N3000 switches.
5. Reload the N3000E-ON Stack and N3000 stack.
6. After stacks are reloaded, download and activate the mixed-stack firmware image
(N3000N3100AdvLitev6.5.3.6.itb) on both stack of N3000E-ON switches and stack of N3000 switches.
7. Reload both N3000E-ON and N3000 Stacks again.
8. Power OFF both N3000E-ON Stack and N3000 Stack of switches. Plug-in mini-SAS stack cables and form
the stack of N3000E-ON and N3000 Series switches.
9. Power ON stack (Stack of N3000E-ON with N3000 Series switches).
Preconfig
Status
Model ID
Oper Stby N3048P
N3048EP-ON
backup
current-active next-active
6.5.3.6
6.5.3.6
6.5.3.6
6.5.3.6
Plugged-in
Switch
Model ID
Status
N3048P
OK
N3048EP-ON
OK
6.5.3.6
6.5.3.6
Page 7
Code
Version
6.5.3.6
6.5.3.6