AVYCON AVR-HT832A-40T 빠른 시작 매뉴얼

{카테고리_이름} AVYCON AVR-HT832A-40T에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AVYCON AVR-HT832A-40T 2 페이지. Hybrid dvr

페이지 인쇄

(Digital Video Recorder)

Quick Start Guide

Please read these instructions carefully and store them in a cool dry place for future reference. All the examples

and pictures used here are for reference only. There may be several technically incorrect diagrams or printing

errors in this manual. Any updated information will be added to successive versions of this manual. The

contents of this manual are subject to change without notice.

1. Notes

- Please read these instructions carefully and store them in a cool dry place for future reference

- All the examples and pictures used here are for reference only

- The contents of this manual are subject to change without notice.

- This device should be operated only from the type of power source indicated on the labeling.

Please verify that the voltage used matches what is indicated on the labeling.

2. Packing Check

Please inspect the device and accessories after purchasing the device. If there are

any visible damages, shortages or defects, please contact your dealer or distributor

immediately.

3. HDD Installation

This model of recorder supports 8 internal SATA hard drives. The following pictures

and diagrams of the HDD installation are for reference only and there might be slight

differences in the actual hardware received. Please make sure that the device is

powered off before the installation.

① Remove the chassis cover and loosen the screws to remove the two HDD

mounting bars.

② Align the HDDs to be installed to their proper mounting holes and secure the

HDDs onto the mounting bar with included screws.

③ Re-install the two HDD mounting bars with HDDs attached and make sure to

tighten mounting bar screws.

④ Connect power and data cables to all HDDs installed.

⑤ Replace chassis cover and make sure to secure it with the included screws.

Tip: Before securing chassis cover, double-check all power and data connections

to HDDs and mainboard.

Hybrid DVR

4. Rear Panel Instructions

Diagram of rear panels below are for reference only.

Name

VGA

VIDEO IN

LAN

USB

ALARM IN

ALARM OUT

GND

P/Z

K/B

AUDIO OUT

AUDIO IN

e-SATA

HDMI 1

HDMI 2

5. Startup & Shutdown

Startup

① Connect recorder to monitor with VGA or HDMI cable and power on device.

② The device will boot and the power indicator will display blue.

③ After completely booting, a Startup Wizard should appear on the screen.

Shutdown

① Click on "Start" button in lower-left corner of the screen and then select

"Shutdown" icon. This will bring up a shutdown window.

② From within this new window, choose "Shutdown". After recorder has completely

shut down, you can disconnect the power.

Description

Connect to monitor

Connectors for Video input

Network Port

Connect to USB storage debice or USB mouse

Alarm input for connecting sensor

Relay output; connect to external alarm

Ground

Connect to speed dome. Y is TX +,z is TX -

Connect to keyboard. A is TX +, B is TX -

Audio ouput

Audio input

Connect to HDD with e-SATA interface

Connect to high deﬁnition display device

6. Login

Username

admin

Password

Enter Password

Display Password

Edit Security Question

The default username is admin and the default password is 123456. You must conﬁgure

the wizard if you start the DVR for the ﬁrst time and you may change the password

when you conﬁgure the wizard for the ﬁrst time. You can skip the settings of wizard next

time. Click "Start" and select "Login". This will take you to see a login box.

Enter default username and password you set and you can see the live image.

7. Analog Camera Connection

First connect the camera to the DVR. Then go to Start>Settings>Camera>Manage

Camera>Camera Signal to checkmark the video mode. The actual signals input shall

correspond to the video mode. Please refer to User Manual for details.

8. Network Configuration & Add IP Camera

After you ﬁnish adding your analog cameras, you can see their live video streams

through the monitor connected to the DVR. The following instructions will mainly

introduce how to add the IP cameras via LAN/WAN.

LAN

① Most networks will be conﬁgured for assigning an IP address automatically through

the router. After connecting this recorder to your network, navigate to

Start>Settings>Network>TCP/IP. If using DHCP, make sure that the option of

"Obtain an IPv4 address automatically" is selected. For manual IP address, make

sure to uncheck the "Obtain an IPv4 address automatically" option and enter

in the proper Address, Subnet Mask and Gateway information.

IP Address Settings

Ethernet Port 1 ( Online )

Obtain an IPv4 address automatically

Obtain an IPv6 address automatically

Address

192 . 168 .

1 .

Subnet Mask

Mask Length

0 .

Gateway

192 . 168 .

1 .

Gateway

MTU

1500

Obatin DNS server address automatically

Preferred DNS

192 . 168 .

1 .

Alternate DNS

0 .

④ Navigate to Start>Settings>Camera>Add Camera. The DVR will search your local

network for cameras and list them. AVYCON and ONVIF cameras will be supported

automatically. If any AVYCON IP cameras are found, but do not have an IP address

that matches your local network, you can click on the Edit button

and modify the IP address directly from the DVR.

Add Camera

Quickly Add

Manually Add

Mac Address

Address

No.

Port

Edit

Subnet Mask

Protocol

Model

Version

Address

Subnet Mask

192.168.2.45

255.255.255.0

XXX

4.0.0.1.beta1

Gateway

Username

Password

Selected: 1/1

Remain Bandwidth: 10 / 10 Mb

Default Password

Add

Cancel

② To change the ports used by

the recorder, navigate to Start

>Settings >Network >Port. You

can enter a different HTTP port

(default value is 80) and Server

port (default port is 6036).

③ Click "Apply" to save the

settings.

for each camera

Edit IP

CE :98 :23 :75 :35 :22

192 .168 . 1 . 45

Sync to IPC

255 . 255 . 255 . 0

192 .168 . 1 . 1

admin

Cancel