360 Vision Visiondome-VR 설치 및 구성 매뉴얼 - 페이지 12

{카테고리_이름} 360 Vision Visiondome-VR에 대한 설치 및 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 360 Vision Visiondome-VR 16 페이지.

페이지 인쇄

Visiondome VR Installation Manual Ver 2.7

8 OSD Operation/Navigation

Dome menu

Seek Preset

•

Start Tour

•

Start Mimic

•

Dome Settings Menu

•

Define Tour

A tour of presets is stored in the Visiondome VR as a list of tour points. Each tour point consists of a preset

number, the dwell time for which the Visiondome VR will pause and the speed parameter that will be used to

seek the preset. Each of the four tours of presets can contain between 2 and 360 points.

When programming a tour of presets it is necessary to first store all the required presets into the Visiondome

VR and to define the required dwell times and speeds of travel that you will require the Visiondome VR to use

when the tour is started.

A maximum of four individual tours of presets can be stored in each Visiondome VR. Each tour can have

between 2 and 360 points, each point can be a preset in the range 1 to 360. Different points can use any preset

number, including repeats of ones that have been used before. The speed that the camera will travel at to reach

the preset can be in the range 1°/sec (slowest) to 100°/sec (fastest). To seek the preset at maximum speed, set

speed to 0. The delay (dwell) at each point is defined in seconds, range 1 to 100.

This page will open on Tour 1, use the joystick left and right to change to another tour. To add item 1, use the

joystick to tilt down. This will highlight the number line so that the tour can be programmed. Use the joystick to

navigate along the number line and zoom in to select the number. This will add the number in to the NEW tour.

Add in the figures for the item/point in the tour using the sequence labelled above (PREDELSPD. PRE is preset

position, DEL is delay in seconds and SPD is speed at °/second). This is how the camera will be programmed to

move to a preset for a period of time at a set speed. All nine figures must be added into the item. Figures must

be added in three i.e. preset 21 will be added as 021.

Example of an item/point

021005100 = Move to preset 21 for 5 seconds at 100°/sec

Highlight ACCEPT ITEM and zoom in, this will add the item/point into the tour. The OLD item/point will be shown

on the screen. If these settings are acceptable, highlight the ACCEPT ITEM option and zoom in. There is no

need to add in these points again. Keep adding points until the tour is complete. On the final item/point of the

tour highlight and zoom in on ACCEPT FINAL ITEM. This will complete the tour programming.

Define Mimic

When a mimic tour is started, the Visiondome VR will perform all the actions which were defined when the

mimic was programmed. Up to four mimic tours can be defined.

Before going into the OSD screen to programme a Mimic tour it is recommended to move the camera in to the

start position, any movement or delay will be recorded once the recording has started.

Highlight and zoom in on START RECORDING, this will allow a mimic tour to be programmed into the camera.

The mimic tour can then be used to playback any manual movement, preset seek or delay. Program a preset to

end the mimic tour program.

Define Preset

Before going into the OSD screen to programme a preset, the camera must be in the position required. Once in

the OSD you cannot manually move the camera.

Define Home Function

The camera will perform an ACTION (goto preset, start preset or mimic tour), after a period of inactivity. Use the

NUMBER option to set which preset or tour to start, and the DELAY MINUTES/SECONDS to input the inactivity

time period.

Page 12