HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER 매뉴얼 - 페이지 21

{카테고리_이름} HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER 24 페이지. Intervideo ã¥â®â¶ã¥âºâ­ã¥â½â±ã©â„¢â¢ ã¥â¿â«ã©â‚¬å¸ã¥â€¦â¥ã©â€”â¨ã¦å’‡ã¥ââ€”
HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER에 대해서도 마찬가지입니다: 사용자 설명서 (37 페이지), 지원 매뉴얼 (27 페이지), 매뉴얼 (10 페이지), 빠른 시작 매뉴얼 (8 페이지), 시작하기 매뉴얼 (2 페이지), 중요 정보 (1 페이지), 중요 정보 (1 페이지), 중요 공지 사항 (1 페이지), 보충 설명서 (1 페이지), 지원 매뉴얼 (29 페이지), 매뉴얼 (8 페이지)

페이지 인쇄
HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP CHARGER 매뉴얼
3 The memory module can be installed in only one
way. Match the notch on the module with the tab
on the memory socket. Push the module carefully
and firmly into the slot, ensuring that the latches on
both ends snap into place.
4 Replace any cabling that was removed.
5 Complete the procedures to replace the side panel
and close the PC. See "Opening and Closing the
PC" page 1.
Removing or Installing an
Add-in Card
An add-in card is a circuit board, such as a PCI or an
AGP card that fits into a PC add-in card slot. Your PC
contains several add-in card slots that can be used to
add components to your PC. The PC component
configurations vary by model.
WARNING: Do not overload the system by
installing add-in cards that draw excessive
current. The system is designed to provide
2 amps (average) of +5 V power for each
board/card in the PC. The total +5 V
current draw in a fully loaded system (one
with all add-in card slots filled) must not
exceed the total number of slots multiplied
by 2 amps.
A Phillips screwdriver is needed to remove, replace,
or add an add-in card.

Removing an Add-in Card

1 Complete the procedures to prepare the PC and
remove the side panel. See "Opening and Closing
the PC" on page 1.
2 Gently lay the PC on its side.
3 Inside the PC, locate the add-in card slots on the
motherboard.
4 If you are replacing a card, make a note of any
external or internal cables attached to the card,
and then disconnect them.
5 Remove the add-in card slot cover by removing
the screw and then removing the cover from the
chassis.
Or
Loosen the screw on the card you are replacing.
Hold the card at the top and carefully pull the card
straight out of the add-in card slot.
Upgrading and Servicing Guide
17